Jump to content
SAU Community

Recommended Posts

Well... Depends on how anal you are about it. You could go to a paint shop, get some paint mixed up according to your existing colour then spray it, that'd cost like $30-40 but it will be a closer match than what the prepacked cans would be.

hmmm thts true...if i go cheap on the paint....the car is gona look shit....may be it will be better if i paint the spoiler along with the full bodykit.i think tht will be much more convinient.....it says needs arund 1000k for full bodykit fitment and spray.....

If your bodykit is brand new and doesn't need repairing.. I'd try DIY first lol.

Like you said, whats the worst that can happen? If you try DIY for the whole kit & spoiler for $100, if you stuff up, you've learnt a $100 lesson, but if you like the quality, you save $900 :P

I DIY my front bar and I'm pretty happy with it, $80 (include ALL the materials) compare to $300.

Charles, difference is yellow is yellow...silver is always different and wears differently. I had a paint mixed up for a mates car and it didn't match. Too risky. If ur spending money on touch up DIY and it screws up and u STILL have to take it to a panel shop you're more out of pocket only uve wasted effort too trying to DIY it. Better to just do it professionally straight up and know it'll be done right. I'd never touch my car with DIY paint as a longterm solution, and mines white. Matter of opinion I guess

Charles, difference is yellow is yellow...silver is always different and wears differently.

>_< What a silly assumption that is. Any paint which contains layers of pearl, regardless of colour, is not a simple match.

Matter of opinion I guess

Indeed.

Possibly, never owned a car that ha a color :P all 3 of mine have been white. The skyline is actually the whitest of em :P even though the pulsar wa technically the same from memory (qm1). Either way, I'd still be having it done professionally. Which is why my car still has scratches on the front bar where some Cnut backed into it while I was at work...again. Matter of opinion

Well I guess since I did mine as a short term solution (until someone runs into me at fault lol), I don't really care THAT much about it.

But then again, as for paint matching, if you were to just spray a body kit, hardly anyone can match it to your car 100% perfectly, unless you blend the new colour into panels, which will cost even more...

I guess it just depends on the person and fussy they are.. Because paint will never match 100% if sprayed at different times, but can be REALLY REALLY close (almost unnoticable to untrained eyes).

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...