Jump to content
SAU Community

Recommended Posts

Ive seen both the RB20DET and the RB26DETT wiring diagrams and they look the same.

1 Ign signal (power transistor) Cyl #1

2 Ign signal (power transistor) Cyl #5

3 Ign signal (power transistor) Cyl #3

4 AAC valve

5 engine. A/T control input signal (bt1)

6 Sub electrical fan relay (engine temp switch)

7 Tacometeter speed signal

8 -

9 AC relay (AC cut signal)

10 Ground (ign signal system)

11 Ign signal (power transistor) Cyl #6

12 Ign signal (power transistor) Cyl #2

13 Ign signal (power transistor) Cyl #4

14 engine. a/t control input sigal (bt2)

15 engine. a/t control input sigal (bt3)

16 ECCS relay

17 -

18 fuel pump relay

19 Power steering switch

20 Ground (ignition signal system)

21 (RX) Receive (control unit data reception)

22 (TX) Transmit (data sent from control unit)

23 Detonation sensor 1 (cyl 1-3)

24 Detonation sensor 2 (cyl 4-6)

25 -

26 Air flow meter ground

27 Air flow meter intake air quantity signal

28 Engine temp sensor

29 Exhaust gas sensor

30 Sensor ground (throttle sen, ENG temp)

31 (CLK)Clock (syncronization signal)

32 Monitor and check lamp (red)

33 -

34 Air flow meter ground

35 Air flow meter intake air quantity signal (front)

36 Intake air temp sensor

37 -

38 Throttle opening output

39 -

40 -

41 Crank angle sensor (120degree signal)

52 Crank angle sensor (1 degree signal)

53 Vehicle speed sensor

54 Throttle valve switch (idle connection pt)

55 Exhaust gas sensor (rear)

56 Throttle sensor output signal

57 Throttle valve switch power supply

58 Battery power supply

59 Control unit power supply

60 Ground (control unit)

101 Injector #1

103 Injector #3

104 Fuel pump terminal voltage control output

105 Injector #2 107 Injector ground

108 Injector ground

109 Injector power supply

110 Injector #5

112 Injector #4

114 Injector #6

115 exhaust gas sensor heater ground

116 injector ground

pic no longer works, wiring diagrams can be found at this link http://www.meggala.com/partcss.htm

Edited by Skyline_Boy
Link to comment
https://www.sau.com.au/forums/topic/37522-wiring-diagrams/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • To be fair passengers who aren't silly and have been in proper fast cars have often been pretty impressed once you hit 4th gear   
    • I suppose that's true. Barring almost any situation, I'll never sell so what the market does is kind of irrelevant to me. It's possible I'd make most of my money back. That spreadsheet I mentioned? Maybe I could make back more than what the car's total costs thus far are, but the parts and all that is possibly a different story... Thanks for reading. It was certainly a good moment and just makes the ties to the car that much stronger. It's exciting that the option will be there to bring it over, however I have some plans with a shop that may end up keeping the car there longer, not sure. Coupled with the fact I want to move there and haven't solidified any path yet. So in a way, it feels like I'm in a limbo state that is uncertain; time will tell.
    • No worries, everything worked out in the end. I just wanted to make the point that it doesn't matter where it comes from (I.E Australia), it can be broken or improperly built. I would still purchase from these companies in the future. B2R - Not certain how that finished, this was on a car I wired a few things and street tuned. I know the owner ended up shipping the motor back to Australia for investigation. Hopefully some of it is covered under warranty.  Turbosmart - I always pressure test everything that goes on my car. It's a habit from my career in oil and gas. I run two 40mm's and both had major leaks from the actuator to exhaust portion through the shaft. I returned both, they shipped me back two and one was leaking and the other had a 38mm top (40mm gate with 38mm actuator cap, no idea how that happens). Eventually after a lot of back and forth I found myself with two non-leaking gates. I believe this happens a lot more then people would like to believe but you would never know if you don't pressure test them prior to installation. Crank Motorsport - Issued a full refund and let me keep the seat rails. I turned them into scrap metal for other projects. GKTech - Shipped me out a replacement and asked that I modify it as per my idea and that they would do the same for a future revision. ATP - Can just needed a large shim to bolt up properly.  Haltech - They started an actual proper Beta channel for firmware's a few months back and stopped using the general public for testing. I'm now much happier.  Speedtek - f**k Speedtek. I would love to watch them burn.     
    • I've got a Turbosmart wastegate, ATP catch can, many GK Tech parts and Haltech everything. Everything's been perfect, sorry to hear your experience wasn't the same
×
×
  • Create New...