Jump to content
SAU Community

Recommended Posts

Hey guys,

if this is happening to you: post-36975-0-95260700-1314502383_thumb.jpg

then you need to replace the little heater core at the back of your dash as it has started leaking. My signs were: strong smell of coolant in the cabin, front windscreen fogging up, loss of coolant in the reservoir and then at the end of it my passenger foot well started leaking coolant.

As I have already removed my aircon line because it split years ago, I didn't need to worry about disconnecting the aircon lines... if you do this, you will loose all the gas in your aircon.

Tools: phillips heads, flat heads, maybe pliers, spanner set, possibly socket set

Should be about an hour to get it out..

1. Remove Glove box - There are 4 screws at the top and 2 plastic tabs at the bottom of it where it hinges to remove.

post-36975-0-70939300-1314502605_thumb.jpg post-36975-0-64857800-1314502608_thumb.jpg

2. Remove plastic backing to glove box which hides aircon evaporator thingy - I think there is just 2 screws and then a decent tug should do.

post-36975-0-73577000-1314502706_thumb.jpg

3. This is what you should see, this is the aircon evaporator, we need to remove it.

post-36975-0-21777200-1314502767_thumb.jpg

There are 4 screws holding it in, plus 3 electrical plugs, plus the 2 aircon lines(mine was already removed)

post-36975-0-07964300-1314503118_thumb.jpg

post-36975-0-84180100-1314504173_thumb.jpg

4. Once all those are disconnected, give it a good smooth tug and this is what you should see:

post-36975-0-30403000-1314503278_thumb.jpg post-36975-0-05497000-1314503298_thumb.jpg

Now we need to get back here

post-36975-0-67719200-1314503335_thumb.jpg

5. But before you do, disconnect the lines going to the heater core or coolant will spill all over you

post-36975-0-52522600-1314503501_thumb.jpg

6. Now, back under the dash at the back there are 4 phillip head screws per line, undo the screws plus one screw for the plastic tab that holds the core in place.

post-36975-0-11170700-1314503667_thumb.jpg

7. Thats it! you should now see this

post-36975-0-72984600-1314503715_thumb.jpg post-36975-0-04787800-1314504012_thumb.jpg

Gently slide it out trying to point the holes up as much as possible so they don't spill

Yep... its leaking...

post-36975-0-19801400-1314503869_thumb.jpg post-36975-0-52807000-1314503795_thumb.jpg post-36975-0-72431900-1314503808_thumb.jpg

So this is what you will be left with...

post-36975-0-39667100-1314503965_thumb.jpg

Get a replacement ($60-100) and do the reverse, top up some coolant (check for air locks etc) and your back on the road

Adam

  • Like 1
  • 2 weeks later...

Mine done same thing. I decided on new core and removal of dash.

Done dash before so was eazy. And that way you dont need to regas aircon.

I ended up getting new core dont want to same thing to happen anytime soon.

Btw great writeup :)

  • 3 months later...
  • 1 month later...

Update - I picked up a complete (whole plastic box + lines and heater core) in great condition for $70.

Awesome cheers heaps for that that'll make it alot easier now shouldn't take to long i hope but if it does oh well

thanks heaps man.

Cheers Toby

  • 3 weeks later...
  • 3 weeks later...

Ok my gone now and have done the bypass as well but I have a question to the above tutorial as in ....

What if youu still have a valid working air conditioning unit and how dowes this change the procedure to change the heater core?

Dazza

If you want to retain your aircon in a working state while doing this you have to literally remove the entire dash to get back there so you don't have to undo the aircon lines - as soon as you open them you will release the gas = no more aircon.

I'm going to put the aircon lines back in my car soon and get them regassed.

IMHO though, even if I had aircon at the time when this happened, I would still fix it the way I did above and just get the aircon regassed for ~$100 then to spent 4-6 hours just removing the dash instead of 1 hour.

  • 8 years later...

Heads up on this useful guide. Just changed out my R33 core sourced from Kudos motorsport. I removed the passenger seat, was quite comfortable laying there on the carpet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ok interesting i guess ill wait till using a manual gauge before making assumptions.
    • Not in any way a logical conclusion. Also, looking at those logs, I struggle to see how that much oil pressure can go away that fast unless you are sucking air into the pickup. Meanwhile the ECU voltage is chucking a huge wobbly which seems to be tied to the throttle position. 100% throttle results in decreasing voltage. It's a mess.
    • So didn't get around to installing a manual oil pressure gauge and then decided to take the car for a cruisey drive to a cars and coffee and brought the laptop along with to get another log using more gears to see if its an oil pressure issue under acceleration or after. this log has 3 gears of WOT where as previous had 2 and the oil pressure dropped once on the brakes, and the same again happens here which is interesting as it shows it can hold oil pressure while under acceleration but once slowing or just the lower RPM after a pull pressure drops. I will be chucking a manual oil pressure gauge on to confirm but so far this makes me feel it is not an electrical issue. Something else i realised is the pressure sensor also is giving temperature information and the temp stays steady the whole time which makes me feel like the sensor itself is showing a true pressure reading.
    • LOL.... fk...   there goes 25K to make 200kW
    • For sure the later RB26 variants had a different setup (6 cam voltage sender?), but the RB25DE/DET share the same ECU pinout/PCB footprint, and at the ECU plug it ends up being 'throttle sensor in' & 'throttle sensor out' (to A/T TCU) ...you stick a multimeter on these pins and you'll find them directly connected (0 ohms) ; I had an pair of Nissan ECUs on the bench long ago, and I noticed this throttle sensor in/out link, actually linked to an op-amp ...which was unpopulated on the NA board, but present on the T board and I went 'ah-ha!' in some moment of clarity... ...it wouldn't surprise me if they changed strategy here though (in the software and actual monitoring of this signal), because they did with other stuff (A/T signals).. and 0.45v as a trigger point makes sense, as that's what the external TCU units expect at idle ; kudos, thanks for that insight...I suppose it boils down to whether or not Consult can display real time data of that signal's voltage... ...in any event, it presents the same target...ie; rotate TPS unit to achieve 0.45v to suit both ECU&TCU, and where do you goto from there? Just disconnect TPSwitch connector and/or that plus TPSensor connector....or do you go for the throat and disconnect IACV solenoid and see if it still stalls? (probably throws a recoverable fault code and goes for default idle strategy?)...
×
×
  • Create New...