Jump to content
SAU Community

Recommended Posts

Hey guys,

if this is happening to you: post-36975-0-95260700-1314502383_thumb.jpg

then you need to replace the little heater core at the back of your dash as it has started leaking. My signs were: strong smell of coolant in the cabin, front windscreen fogging up, loss of coolant in the reservoir and then at the end of it my passenger foot well started leaking coolant.

As I have already removed my aircon line because it split years ago, I didn't need to worry about disconnecting the aircon lines... if you do this, you will loose all the gas in your aircon.

Tools: phillips heads, flat heads, maybe pliers, spanner set, possibly socket set

Should be about an hour to get it out..

1. Remove Glove box - There are 4 screws at the top and 2 plastic tabs at the bottom of it where it hinges to remove.

post-36975-0-70939300-1314502605_thumb.jpg post-36975-0-64857800-1314502608_thumb.jpg

2. Remove plastic backing to glove box which hides aircon evaporator thingy - I think there is just 2 screws and then a decent tug should do.

post-36975-0-73577000-1314502706_thumb.jpg

3. This is what you should see, this is the aircon evaporator, we need to remove it.

post-36975-0-21777200-1314502767_thumb.jpg

There are 4 screws holding it in, plus 3 electrical plugs, plus the 2 aircon lines(mine was already removed)

post-36975-0-07964300-1314503118_thumb.jpg

post-36975-0-84180100-1314504173_thumb.jpg

4. Once all those are disconnected, give it a good smooth tug and this is what you should see:

post-36975-0-30403000-1314503278_thumb.jpg post-36975-0-05497000-1314503298_thumb.jpg

Now we need to get back here

post-36975-0-67719200-1314503335_thumb.jpg

5. But before you do, disconnect the lines going to the heater core or coolant will spill all over you

post-36975-0-52522600-1314503501_thumb.jpg

6. Now, back under the dash at the back there are 4 phillip head screws per line, undo the screws plus one screw for the plastic tab that holds the core in place.

post-36975-0-11170700-1314503667_thumb.jpg

7. Thats it! you should now see this

post-36975-0-72984600-1314503715_thumb.jpg post-36975-0-04787800-1314504012_thumb.jpg

Gently slide it out trying to point the holes up as much as possible so they don't spill

Yep... its leaking...

post-36975-0-19801400-1314503869_thumb.jpg post-36975-0-52807000-1314503795_thumb.jpg post-36975-0-72431900-1314503808_thumb.jpg

So this is what you will be left with...

post-36975-0-39667100-1314503965_thumb.jpg

Get a replacement ($60-100) and do the reverse, top up some coolant (check for air locks etc) and your back on the road

Adam

  • Like 1
  • 2 weeks later...

Mine done same thing. I decided on new core and removal of dash.

Done dash before so was eazy. And that way you dont need to regas aircon.

I ended up getting new core dont want to same thing to happen anytime soon.

Btw great writeup :)

  • 3 months later...
  • 1 month later...

Update - I picked up a complete (whole plastic box + lines and heater core) in great condition for $70.

Awesome cheers heaps for that that'll make it alot easier now shouldn't take to long i hope but if it does oh well

thanks heaps man.

Cheers Toby

  • 3 weeks later...
  • 3 weeks later...

Ok my gone now and have done the bypass as well but I have a question to the above tutorial as in ....

What if youu still have a valid working air conditioning unit and how dowes this change the procedure to change the heater core?

Dazza

If you want to retain your aircon in a working state while doing this you have to literally remove the entire dash to get back there so you don't have to undo the aircon lines - as soon as you open them you will release the gas = no more aircon.

I'm going to put the aircon lines back in my car soon and get them regassed.

IMHO though, even if I had aircon at the time when this happened, I would still fix it the way I did above and just get the aircon regassed for ~$100 then to spent 4-6 hours just removing the dash instead of 1 hour.

  • 8 years later...

Heads up on this useful guide. Just changed out my R33 core sourced from Kudos motorsport. I removed the passenger seat, was quite comfortable laying there on the carpet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My take on gg2 48mm, 54mm, 58mm, and 62mm compressor map for same size compressor vs gg1 : All gg2 only outflow gg1 above 20 psi. As all g gen 2 surge line at lower left of comp map move to the right, all gg2 sacrifice spool vs same size gg1, surge line move to the right worst for 54mm gg2. So for same size compressor if you want best response, use gg1, if you want max hp at >20psi use gg2 but you will be laggier vs same size gg1. Max compressor efficiency drops to max 75% on all gg2 vs max 76%-80% of same size gg1. Iirc lower efficiency means hotter iat less dense air so lower hp at same operating point of comp map. Also curious why gg2 is mapped to lower max rpm vs same size gg1 (only 48mm size both gg1 gg2 mapped to same rpm) : 54mm gg1 165,000 rpm  vs  gg2 160,000 rpm. 58mm gg1 150,000 rpm vs gg2 140,000rpm. 62mm gg1 145,000 rpm vs gg2 140,000 rpm. If gg2 can safely spin to gg1 rpm then they can flow a bit more than as mapped. Good thing that all gg 2 interchange compressor and turbine housings with same size gg 1. So gg1 owners can buy gg2 chra only if planning to boost >20psi.
    • My stuff is all with Shannon's, granted, I don't really have imports I'm driving on the road, however, I've had multiple cars at the same time with them. Presently we have the Landcruiser on laid up cover, Sarah's Kluger on full cover, and the house insured. About 18 months ago Sarah wrote her Subaru Liberty GTB off, insured with Shannon's, and the payout, and buy back of the wreck was super quick. In 2020 we had the VF Commodore totalled in a major hailstorm. Storm was on the Saturday, I called on the Sunday and lodged it, vehicle was towed on Tuesday night, assessment team called on Wednesday to say it was a total loss and get payout details, money was in the bank on Thursday morning. Have had a few other claims both at fault, and not at fault, over the years, and never had an issue with them.   Funnily enough, they're also the cheapest insurer I find for things like Sarah's Kluger.   I will say I'm less impressed dealing with them lately around "the experience", as a lot of their staff that you deal with aren't car enthusiasts. Shannon's has a much more main stream feel ever since they decided to become "big corporate", laid a heap of staff off, and then hired a bunch of non enthusiasts. At the same time they've been making a push to be less "call us and we'll personally have someone who cares help" to "hey, this computer can do stuff for you" and are trying to get more square pegs to fit round holes. (That's just the vibe I get from them). Again, have had no issues with claims with them, but get a bit of a "less personal" feel from them.
    • A thing I wasn’t happy with with enthusiast was during the initial phone call they told me they’d insure it for 130k but needed photos.   I then sent them photos and they told me $80k as there were other cars either similar modifications available for around that price, I told them to send me the links to said cars so that I can buy them. i then sent the modification list with prices of the parts (no labor) and the price then came to 115k, which is still shy of the 130 that was agreed in the initial phone call 
    • Ask me a bit later this week before payday
    • I agree that delayed payment probably isn't the most suitable solution. It seems a solid complete transaction would be best. As I wouldn't be using this sale as a line of credit that would typically earn interest, we can probably arrange a much cleaner single transaction deal. I can do $92.52 today. Would you prefer EFT, or Cash on Pickup?  😛
×
×
  • Create New...