Jump to content
SAU Community

Recommended Posts

I parked my car in Bayview today to go out and do a spot of fishing, about 1.5 hours later I get a call from my brother in law saying both of my wing mirrors have been broken off their mounts and both of my antennas (AM/FM radio and a two way radio antenna) have been bent over and destroyed. What's fortunate is my brother in law saw the woman break my drivers side mirror, and then go into her house (my car was on the public space outside her house). We've since worked out between us that she feels that spot is "hers" - the street is notoriously difficult to find parking spots on, although today all afternoon there was HEAPS available. She must have already been in a foul mood to vandalise a car that's never parked there before. Unfortunately, the police spoke to her and she denies everything. They want to fingerprint the car tomorrow to see if they can lift any prints off the mirrors which unfortunately means I'm going to miss the September Texi. She has even volunteered to be fingerprinted so I'm sure she pulled her sleeves over her hands when doing the damage, and most likely I'll be out of pocket and miss a motorkhana day. However, that kind of vindictive damage is not something I can let pass so I want to see her be held accountable for it and letting the police do their fingerprinting is the best way at this stage to achieve that.

So as far as the car damage goes shit happens, 2 mirrors and 2 antennas can be replaced. What has me angry is her attitude to the whole thing, she was caught in the act and now she's denying everything. The police have already said if they can't get prints off it then they won't have enough evidence to proceed further. The only comfort at this stage is that to do that at the drop of a hat she must be a petty, unhappy person in life and aside from this event I have had one of the best fortnights in recent memory so there's certainly a lot else in life to be thankful for.

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/
Share on other sites

my brother in law saw the woman break my drivers side mirror, and then go into her house

Can I assume that your insurance company can use this ^ ^ ^ information + the police report?

I empathise with you Geoff; but so too should your insurance company claims dept who have access to their own legal experts perhaps?

Corinne will know...

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5997865
Share on other sites

Hi Terry,

Thanks for the advice, I certainly plan to speak with my insurance company (Corinne and Chubbs are both quite familiar with the one I use) but I'll wait until later tomorrow when I have more information about the situation.

The physical damage sucks but it's easily fixed. What really gets to me is the attitude of the person who did it - the lack of respect for other peoples' property and the brazen nature of it is just staggering.

Cheers

Geoff

edit - lol, touche :D

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5997879
Share on other sites

thanks for the offer Cass, I'll see how the chips fall tomorrow. In my book if you cause damage to someone's property you should A) own up to it and B) make it better but since A isn't happening I don't think B will be an easy task..

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5997923
Share on other sites

Hmm, very interesting, usually some people will take justice into their own hands after knowing who did the crime and where they live. Bravo on not going ape shit. Although I'd just torment the bitch via childishly sending pizza orders every now and again buy a trailer and happily leave it parked in the same spot 24/7, 7 days a week and pay the registation happily and finaly chuck in a few prank calls every know and again from a pay phone at the early hours of the morning.

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5998069
Share on other sites

That blows Geoff, I cannot stand vandals or for that matter anyone that takes pleasure in destroying the property of others.

As others said, well done on remaining level headed about the whole thing - It would have been a totally different story if she did it to my car!

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5998084
Share on other sites

Hmm, very interesting, usually some people will take justice into their own hands after knowing who did the crime and where they live. Bravo on not going ape shit. Although I'd just torment the bitch via childishly sending pizza orders every now and again buy a trailer and happily leave it parked in the same spot 24/7, 7 days a week and pay the registation happily and finaly chuck in a few prank calls every know and again from a pay phone at the early hours of the morning.

+1 to this, takeaway would be comming form all diffrent directions

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5998147
Share on other sites

At least they are fixable and that you can still drive it. Imagine if you were in an area known to just set fire to vehicles out of anger or just boredom.

Kudos to you for not losing your cool.

If the insurance doesn't go to well, just follow the steps:

Step 1: buy some illegal substance

Step 2: put this illegal substance in their mailbox/slip it under their door/throw it into their backyard

Step 3: tip off the police that she is either a known user/dealer

Step 4: giggle your mother f**king ass off

Step 5: ???

Step 6: PROFIT!!

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5998211
Share on other sites

Can I assume that your insurance company can use this ^ ^ ^ information + the police report?

I empathise with you Geoff; but so too should your insurance company claims dept who have access to their own legal experts perhaps?

Corinne will know...

Sorry to be the bearer of bad news but unless the cops can nail it too her your shit out of luck on this one :(

Link to comment
https://www.sau.com.au/forums/topic/376043-bayview-vandal/#findComment-5998332
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
    • Well, do ya, punk? Seriously though, let's fu<king go! The colour and kit looks amazing on the car. Do you have any shots from the rear? I don't quite follow how the model came around. You bought the white kit and he modified it to match your car? Looks nuts either way!
    • So my car is finally back from paint! This took an absolutely insane amount of work and should get it's own build thread - but I didn't build it. It was completed by Troy @ https://scalekustoms.com.au/ I originally bought the AOSHIMA URAS Type R kit while I was in Japan, it's supposed to look like this when assembled: Now, I thought that was cool enough until I opened the box with Dismay, as there's no way I could possibly have completed it. The thing is 1/24 and has details down to the steering wheel horn button, which is a 2mm diameter sticker. I originally wondered if someone could make it at all, as is - But then things got a little carried away. It's worth noting that the model does not have an openable bonne, let alone engine bay, OR an openable boot. - Troy has worked wonders with 3D printer and presumably better eyes than I will ever have. My photos suck, so I will post up some of his in-progress ones he sent to me during the way. Unsuprisingly, he is very detailed. A lot of these are out of order. But he: 1) Made a LS engine and an engine bay appear out of thin air 2) Made the bonnet removable 3) Printed the rims I will buy in the future (or any rim you want) 4) Printed and added the wing that is going on 5) Tinted my back windows as this is what my car has IRL (privacy glass) 6) Added a licence plate. 7) Somehow did the interior 8) 3D Printed my actual seats 9) Made the exhaust under the car connect even though this is likely invisible. 10) Created a boot with my fking battery box, power steering reservoir, subwoofer and toolboxes back there. To say it's insane is an understatement. And I f**ked it all up because when I was re-mounting the wing (it broke in transit) I spilled glue everywhere and ripped paint up and Gregged the rear half of the car. Which about makes sense. Also, this arrived on the same day. Quite the change from: I spent 16 hours per day over the next 3 days pre-christmas putting the interior back together, mounting lip, fixing various bodykit problems with window mouldings, etc. and servicing, rebuilding my 370z brakes to go on the car 'soon', messing with heights to check clearances for new wheels, etc. I also had a foray into mounting wiper-mounted washer jets which was an absolute disaster. The bodyshop has welded (and painted) over the stock jet locations for reasons unknown to everybody (i.e they forgot) I also wanted to wire in the oil pressure sensor on Christmas Eve which was a BAD IDEA. You do not know terror like pulling your ECU apart, pinning in half-fitting pins that aren't the right ones, but trying anyway because it's Christmas eve, putting your ECU back together and having a no-start condition with a fuel pump not priming. Then you undo all your work and the fuel pump still doesn't prime. So after all that terror and horror and pain and tedious disassembly, the issue was the relay in the boot which seems to have died/stuck when I was turning the car off and on about 700 times testing shitty washer jets. I also re-wired the fuel pump power plug which fell apart in my hands. I am very happy I had 3 extra pre-made ones from a few posts/last Christmas's breakdown. https://bluewireautomotive.com/products/10-x-pcm-ecm-ecu-terminals I have put an order for these in, so I can actually add the pins to the ECU properly. The commodore ECU does not have the pins for Oil Pressure via ODB2. However the ECU can support it if you create the pins and wire them in. So for round two, and somehow attempting to route that into the engine bay through my impossible engine bay grommet is a fight for another day. It's 40C in Melbourne tomorrow, I am half tempted to drive the car with the aircon on to deliver presents to my partner's family and see if it helps with the overheating-on-40C-days-in-traffic-with-aircon-on-only issue that the vents were intended to solve. Do I feel lucky?
×
×
  • Create New...