Jump to content
SAU Community

Need Help On A Exhaust System

r344425gt

By r344425gt,
in Engines & Forced Induction

 Share

Recommended Posts

Jonno34 Mentor

Jonno34

Posted
Posted

mandrel bent 2.5" mild steel custom made system. include 0-2 extra mufflers in the middle of the system, oval muffler on end.

will cost around 600 or so. just go to a local exhaust shop and get one made up.

this topic was covered in a previous post .... MANY times, in fact there was one just yesterday if you had bothered to read.

NISMØ Community Regular

NISMØ

Posted
Posted

There is five different threads about exhaust systems for non turbo skylines on the first page of this section.

They need to put a sticky or something in huge bold writing because every single retard comes into this section of SAU and asks the same question.

Jonno34 Mentor

Jonno34

Posted
Posted

gain performance through exhost?

easy mate, just make the piping as big as possible, 2.5" has been suggested cos its just too expensive to buy enough metal to make 5" piping. bigger piping = tons of air flying right through.

also sticking a whopping great big cannon will make your cars exhaust system be just as powerful as what the name suggests - A CANNON

your skyline will now fly

Jonno34 Mentor

Jonno34

Posted
Posted

okay il be serious now, exhaust isnt a very great way to make more power. in fact anything n/a isnt a very good way to make more power.

this is why you are advised to SEARCH.

in fact, had you searched, you would also have found out that extractors are nastily expensive for the relatively little power they give unless you like to be in mid-high rpm ranges, and even then its still nothing special.

and if you at least did not say "cbf searching" - you would have at least avoided my sarcasm.

Mohsen Grand Master

Mohsen

Posted
Posted

im picking up a nismo 2.5" cat back tonight. ill fit it tomorrow and tell you guys how the car feels.

im guessing it should be pretty good since it is a genuine nismo item for an NA

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Turbo gods, some assistance and recommendations please I'm looking into a turbo kit for my 2.5 from MX5 Mania >>>>> https://mx5mania.com.au/products/copy-of-mx-5-nc-2-5-litre-engine-conversion-turbo-2005-2013 Power wise I would like about 200kw atw, and of course dose noises, apparently if you keep a stock 2.5 under around 200kwatw the engine and drivetrain will not hate life even when ragging on it a bit Max RPM on the 2.5 is around 6500rpm The turbo MX5 use is something around the disco potato size as  packaging room for the turbo is pretty limited, which will, I believe, give me my power goals I want and not have the turbo either under, or oversized, but the rear housing bit is confusing  It comes with either a 0.64 or 0.86 From my understanding, which so far is based off googling, so make of that what you will 0.64: spools faster = good Makes more EGT heat on boost = bad Less topend power than 0.86 = I'm only looking for 200 atw so that point may be mute????, I don't know, hence my questions  0.86: Spools a "little" slower = how much slower??? remembering 6500 is my max rpm Makes less EGT heat = good Makes a little more power up top = again, power goals is only around 200 Also, this is a street car, so there will not really be any long track sessions, in saying this I would want it so it was happy with at least 3 hot laps at Wakefield Park if the need arises  I already have a fancy pants triple pass radiator, and a oil cooler with thermostat will be getting installed as well Thanks for any information or recommendations you have 👍, and of course, the comments about me wasting money on drive in drive out modifications, or any other snide remarks about my manhood for owning a MX5 🤣    
    • The Bogan
      Mistakes were made, my R34 Story

      By The Bogan · Posted

      Tape some wool onto the vent then take it for a drive I did this to my reverse cowl and was instantly unhappy, as anything over about 60kph would have the wool enter the engine bay, thus just adding underbonnet pressure and stooging my coolant stack, it did let alot of heat out when stationary though, which really didn't help once the car was moving, with the reverse cowl you could watch the coolant temps cheap up the faster you went on the hwy, I assume it would be alot worse doing track day speed With the vented bonnet (just after the radiator and about 1/3 up the bonnet) on my old R33 the wool on the leading edge sat at about a 45° angle as air poured out of it From looking where your vents are, and their size, I believe you should be fine at speed and air should be evacuated from the engine bay, I think it will be a night and day difference when stuck in traffic though for removing the trapped heat, and not sitting there cooking when parked up after driving around... #convection  Post wool tuft pics and data for science  This beastie is one nice and unique rig, enjoy
    • GTSBoy
      How much roughly to convert stock r32gtr to single high mount turbo + ecu and tune

      By GTSBoy · Posted

      It is possible to do this stuff for "cheap". But you need to be able to get deals on all the bigger items, and it really helps if you're fully capable of doing your own work. As soon as you're paying retail for new parts, or buying "kits" because you can't fabricate necessary bits and pieces, and if you really need someone else to take the reins of doing the work because you don't have the space/time/skills/confidence to  rip deep into the car and put it back together in a working fashions.....then you pay. And these days, pay means a lot of money. You'd think things would get cheaper, but they don't. They just seem to keep getting more and more expensive.
    • r32-25t
      How much roughly to convert stock r32gtr to single high mount turbo + ecu and tune

      By r32-25t · Posted

      It’s almost the price of an engine build, you won’t have anything to bolt onto it though 
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Hopefully it's enough to help with the temps! I was also only shit stirring, regarding Murphy's Law basically. I've found, what ever spare parts I have, are the parts I don't break. Ever. Also have never had issues with oil/spinning bearings until I put oil pressure gauges on the car. 😛
×
×
  • Create New...