Jump to content
SAU Community

Recommended Posts

Given the people involved, the diagnostics they have been resorting to and generally giving them credit I'd think (or hope) that its almost insulting to make these suggestions on the assumption they weren't the first points of call. It'd be very interesting to see a datalog file as the car warms up, however - if that were a possibility?

You would be suprised

Amount of fuel to flow out of the injector is dependant on the opening time(For this purpose we will ignore injector lag times) and fuel pressure.

The more fuel pressure the more fuel will flow at the same opening time(This is also discounting changes in manifold pressure)

If you have a faulty FPR it could make the fuelling go all over the place.

That said if injectors are not getting a constant good voltage source, injector opening times will change, this will change the amount of fuel being injected but wont nessesarly change the pulsewidth's especially if the ECU is not seeing the same voltage drop

not sure if this is relevant

..but when i got my car tuned originally I had never changed the fuel filter. Must of been dirty, then i changed it oneday giving it a serivce and all of a sudden was running very rich .first got told it was a boost leak ,I thought it was FPR busted cause I had hooked fuel lines up wrong at first, but it was just a filter that changed pressures and threw my whole tune out.. :/

Trent fixed it I dunno how ...had him stumped for a while too...

Since most things have already been pointed out, what about the grounding of the engine to chassis, etc. I know the BA Falcon's have an issue where they would run rich and even stall, all caused by the chassis/motor grounding being installed wrong.

Given the people involved, the diagnostics they have been resorting to and generally giving them credit I'd think (or hope) that its almost insulting to make these suggestions on the assumption they weren't the first points of call. It'd be very interesting to see a datalog file as the car warms up, however - if that were a possibility?

Well it basically has to be one of these things, how else does fuel magically get into the cylinder?

Tried another ECU that isn't a Haltech? I had a *very* similar issue along with some other "electrical gremlins" (intermittent misfiring and some other problems), the Haltech setup had been checked by many people whom could see nothing wrong with it - swapped it out for an Autronic ECU and the car has never run better.

Never did resolve the problems with the Haltech, as said many people had looked at it and said there was nothing wrong with the setup, it just would not work reliably in my car for whatever reason. Power FC had no problem, Autronic has no problem, Haltech had nothing but problems... *shrug* go figure.

Yeah this isn't the first time I've heard of nondiagnosable problems with a haltech, most people end up fixing it by using another ECU.

Might not be the ECU, might be some weird combination throwing it out, but sometimes its just cheaper and less time to try another ECU.

Yeah I was wondering about that too, ECU sounds like it CLAIMS its doing everything right - fuel pressure sounds right, something "lying" is the next most likely option.

yes sadly if you are paying a workshop $100-$150 an hour to diagnose a problem it can often be cheaper to switch to another ecu if the problem is specific to that brand ECU... considering you're likely to recoup 50-70% of what you paid for it the changeover cost to a new ECU may not be too bad.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • I think this is more a question you should ask the tuner. My assumption is you have nothing plugged into the original pin for ring gear crankshaft, which is where your map sensor should get wired to, but now you've asked the tuner to disable it. I'm assuming (because I haven't memorised your setup) you are using RB25 ECU on the RB20 loom, to plug into an RB25. You will want to check what else is connected potentially backwards between the engine, loom, and ECU. You might be all fine and safe. The best solution you could have done is wire in a map sensor, and leave the ECU able to read a map sensor.
    • Alcantara all the things!   
    • These arn't them, but these are the pieces.  I dont think hydrodipping would work. Also, the plastic is very old and brittle, the trims are out of the car atm getting some mounting holes jb welded. 
    • What about hydrodipping? I was looking at it but if the piece is complicated the end result might not be as good, I've seen it recently where if you have a checkered pattern for example and dip it, the area where the plastic bends, those checkered boxes look stretch. Doesn't look terrible but not the best result either.  Every rattlecan job I've seen has turned out crap (at least on the skylines, they are always peeling and bubbling) but I haven't seen anyone get a proper spray gun and compressor and go at it. In theory they should last a lot longer. Vinyl wrap is another option (also difficult if there are a lot of complicated sections)
×
×
  • Create New...