Jump to content
SAU Community

Recommended Posts

Hmm, patience mate, it will be worth it.

I'm using morimoto minis - they basically slot in and you screw a fitting rung on from behind. It doesn't get any easier. Hardest part will be trimming the shrouds and housing.

success.... finally

using a rotary burr I was able to hollow out the H1 base leaving just enough material so that a H1 could still be used if necessary, and so a D2R bulb could be inserted instead..

B8E5520D-911C-4B27-A71D-0DFFC2381A84-2065-000003E0E4ED9BD4.jpg

The D2R bulb and socket sticks out a long way... the bulb is now locked in by 2 screws instead of a spring clip. so yes, replacing a blown bulb is going to be a harder task.

4BE159BA-CE96-473C-95BC-8F6D7BEB444D-2065-000003E170E06C45.jpg

ABF9F3C4-CAAF-4709-93B1-0193C75BBC73-2065-000003E0FB8A864E.jpg

5B40E89A-A286-432D-8299-2A8D1BA8002C-2065-000003E0C6A02AEE.jpg

1FF7A6C7-079B-46A8-A16B-F8EC368FD3FA-2065-000003DF740DB4D6.jpg

i can already see an improvement in light output with daylight filling the garage. when standing an object infront of the car, the cast shadows are much sharper from the new headlight. The beam cutoff line is much cleaner, and there is a fine blue/yellow edge on that cutoff. I'll upload a night pic tonight before my mad rush to reassemble the car.

F27B946D-17FA-4475-B9CE-2FD5E3A9FD4C-2065-000003DF82B9E019.jpg

9FDD9A63-D55F-484E-901B-4C42D19F9336-2065-000003DF63E85848.jpg

Edited by Deep Dish V35

I had those Tai/Japanese import ones in my sedan, they were pretty good once you got the headlight adjustment right on them, just don't do what i did and put them in, put it back together and then check the alignment... or you will become a pro at taking off the front bar rofl.... also if you want to build your own I have a set of headlights here from my 300GT that I can sell you

those front bar mounts are definitely a pain. a quick release clip behind the side indicators instead of the two 10mm bolts would make life easier.

i dont run the undertray anymore so that saves about half an hour

And heres the difference between factory HID and my setup.

Keep in mind, these are both using the factory loom, ballast, and Phillips D2R bulb. The only difference comes down to the reflector in the factory headlamp Vs the parabolic lense assembly in my custom light (aka projector beam)

This is the passenger side OEM HID

1CA23161-8D69-4404-81B3-4A122D92AE3E-2324-00000441130A3730.jpg

this is the drivers side parabolic

7B798782-611D-4D3B-9CDB-777262149C96-2324-000004419A34043A.jpg

and both side by side... you can see how much brighter the road would be infront of the drivers side, the clean cut line, and the blue/yellow light refraction on the top edge.

96F9257A-2F2B-4255-AC2E-8DF023899A67-2324-00000441AE3EA01F.jpg

I love parabolic lights. Modified the ones in my old BMW years ago... and built my own set for my scooter years ago too..

heres something that will dampen your motivation then.....

testing the light in a garage over 7 metres is one thing.... testing it in the street is something different.

it turns out that my custom light beam only travels forwards about 8 metres before fading out real quickly. thats less than 1/4 the distance of the oem assembly. and yet directly infront of the car the light is awesome. You can see in my previous post , on the roller door, a darker spot in the centre of the new beam just below the cutoff. well that spot gets much worse.... i did notice it earlier today and thought "uh oh"

so yes, ive either got a slight alignment issue with the bulb (guessing by about 2mm, entirely possible)..... or its the D2R bulb itself.

research has just told me that the D2R bulb actually has a built-in deflector designed to stop glare when installed in your everyday reflector type headlight like the OEM assembly. this deflector appears to block the area of light that would project directly forwards in a parabolic assembly..... switching the bulb with a D2S should fix this - the D2S is a 99% identical bulb just without that built-in deflector.

so now... i just have to buy a pair and try it.

Edited by Deep Dish V35

yeah i didn't want to dampen your enthusiasm but i think your output pics leave a bit of work to be done.

hopefully the D2S's will help - but i also notice that you did some custome mounting of the bulb and i am pretty sure the position of the bulb inside the arc of the projector lense makes a big difference. I think you might be out of alignment based on the hotspots you can see in your garage shot.

here is an idea of what the morimoto minis look like in terms of output - and they're not conisdered to be up there with the best of them either (unlike LS460's, S2k's, FX-R's etc)

e04d841d-4a8c-4645-b7c1-1ff029dc5989-4.jpg

DSC05085.jpg

knew it wouldnt be right first time hahaha..... but even as is, its better than i was expecting. the arc in the D2R is sitting about 2mm rearward compared to the H1 filament. i didnt want to shave the mounting face of the assembly just yet...

if only they made a H1 HID bulb with the same loom fitting as a D2R...

a universal assembly like yours is obviously the smarter option...

Edited by Deep Dish V35

hmmm

maybe have a look on here, there are lots of different adapters and splitters that might help you get a H1 globe (as you're buying new ones anyway) to PNP with your D2R ballast?

http://www.theretrofitsource.com/product_info.php?cPath=31&products_id=255

if you swing them an email, matt, the business owner will normally respond pretty quickly and with a host of information. I've bought off them a few times now and always based on the advice they give more or less.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, the latter. No diff should have a centre replaced without checking clearances because its unlikely to be the same as whatever came out. Not that that stops most people just checking a new centre in
    • Major thread necro but how bad of a job is it to DIY? Looking at it online it looks like if you reuse your ring and pinion as long as those are in good condition it should be fine to just pull the axles/front cover and replace the diff that way? Or should I be replacing everything and doing preload measurements/gear mesh testing like the factory service manual mentions for the rear diff?
    • in my list I had the R33 GTR as the best Skyline. Infact I had all GTR's (33>34=32), the NSX, the GTO, the 300ZX, the 180SX, the S15 better than the FD RX7. I had the MR2 and the A80 as 'just' better. I also think the DC5R Integra looks better but this is an 01 onwards car. I also think the FC>FD. It's almost like aesthetics are individual! The elements @GTSBoy likes about the FD and dislikes about the 180 are inverse in my eyes. I hate the rear end of the FD and it's weird tail lights that are bulbous and remind me of early hyundai excels. They are not striking, nor iconic, nor retro cool. The GTO has supercar proportions. I maintain these look much better in person (like the NSX) especially with nice wheels and suspension which is mandatory for all cars pretty much. Some (or all) of these you have to see in person to appreciate. You can't write a car off until you see one in the flesh IMO. Like most people we probably just like/dislike cars which represent certain eras of design or design styles in general. I also think the 60's Jag E type looks HORRIBLE, literally disgusting, and the 2000GT is nothing to write home about. FWIW I don't think the Dodge Viper Gen1's have aged very well either. You can probably see where I rate bubbly coupes like the FD. I know we're straying now but the C4 and C5 absolutely murder the Viper in the looks department as time goes on, for my eyes. Wouldn't surprise me if people who love the FD, also love the MX5, Dodge Viper, Jag E Type, etc etc.
    • I used to hate R31s, and any of the other Nissans that led up to it, and any of the Toyotas with similar styling, because of the boxiness. They were, and remain, childish, simplistic, and generally awful. I appreciate R31s a lot more now, but only the JDM 2 door. The ADM 4 door (and any other 4 door, even if they are unique compared to our local one) can eat a bowl of dicks. The Aussie R31 is also forever tarnished by their association with stereotypical bong clutching Aussie R31 owners of the 90s and early 2000s. I think the Nissans of the 70s (other than 120Y/180B/200B) are far superior looking to the 80s cars. The 240K era Skylines are boss. The same is broadly true of Toyotas. Hondas don't ever register in my thinking, from any era. Mitsus are all horrid shitboxen in any era, and so also don't register. Subarus are always awful, ditto. Daihatsus and Suzukis also don't generally register. They are all invisible. I think the SW20 MR2 looks fiddly. The 3000GT/GTO is like that but way worse. Too many silly plastic barnacles and fiddly gimmicks ruined what could have been a really nice base shape. Kinda-sorta looks like a big heavy ST165 Celica coupe (and I'm not sure if that's a good thing or a bad thing). I think the 180SX is dreadfully bland. It's not bad looking. But it has no excitement to it at all. It's just a liftback coupe thing with no interest in its lines, and bad graphical elements (ie wide expanses of taillight plastic on the rear garnish). The S13 Silvia is a little better - getting closer to R32 shapes. But still....bland. S14? Nope. Don't love it. S15...a little better. Probably a lot better, actually. Benefits from not being like a shrunk in the wash R34 (where the S13 was a shrunk in the wash R32 and the S14 looked like a Pulsar or something else from the stable on Nissan mid 90s horrors). The Z32 was hot as f**k when it came out but hasn't aged as well as the A80. Keep in mind that I think the R33 is the most disgusting looking thing - and out of all the previous cars mentioned is objectively closest to my precious R32. It's just....real bad, almost everywhere you look. And that is down to the majority of what was designed in the 90s being shit. All Nissans from that era look like shit. Most other brands ditto. In that context, the FD absolutely stands out as being by far the best looking car, for reasons already discussed. Going behind the aesthetics, the suspension alone makes it better than almost any other car.  
    • If they just called it the "Mazda Tiffany", it would have been spot on.
×
×
  • Create New...