What Turbo do I need?

[CroatianR33]

I have a close to standard R33 gts-t and would like to reach a goal of 250rwkw.

I have been told a GT2535/2540 is suitable for this kind of power. Does anyone have any other suggestions on which turbo i could use, possibly something cheaper as I heard they sell for $4000 which im not sure is true. Its a daily driver so I would like good mid range response.

What will I have to upgrade to run this kind of power safely?

Fuel Pump

Injectors

Tougher Synchros

Oil Cooler

And just remember I am not keen on spending millions of dollars. I just want something that will remain low-mount and make my car a quick street car.

I was also told hi-flowing the standard turbo would only be good for 210rwkw. Is that true?

[Guest two.06l]

I have a close to standard R33 gts-t and would like to reach a goal of 250rwkw.

I have been told a GT2535/2540 is suitable for this kind of power. Does anyone have any other suggestions on which turbo i could use, possibly something cheaper as I heard they sell for $4000 which im not sure is true. Its a daily driver so I would like good mid range response.

What will I have to upgrade to run this kind of power safely?

Fuel Pump

Injectors

Tougher Synchros

Oil Cooler

And just remember I am not keen on spending millions of dollars. I just want something that will remain low-mount and make my car a quick street car.

I was also told hi-flowing the standard turbo would only be good for 210rwkw. Is that true?

HKS gtr-s would be the go with 550cc injectors and bosch motorsport pump mounted in the factory in tank position a gtr intercooler would be nice to see also if you had the dollars.Oil cooler only needed for track racing or drifting so save money and spend it elsewhere. you would also need aftermarket comp management i think microtech make a plugin system thats good value for money Stace Racer :flower:

[SLY33]

hi dude, 250rwkw is no mean feat and should be fairly straight forward.

you will need the fuel pump, a front mount, a clutch, and an programmable ECU. And of course a good free flowing exhaust and filter.

You wont NEED the injectors and as you arent keen on spending heaps, just get a rising rate reg. Your gearbox will cope with the power fine.

A 2535 may hit 250rwkw, the 2540 should definitly hit 250rwkw. But new they cost a bit, so you could always go second hand for ~2grand. Problem may be that the 2535 is a bit hard to find 2nd hand, and the 2540 people dont seem to like!

I went to UAS the other week and looked at a band new Garret 3040 internal gate low mount that will bolt straight up, giving you the stock appearance you want. John at UAS will guarantee you will see 250rwkw, i think at around 1.2-1.3BAR, which you can run safely with the standard compression if the tune is good. UAS also insisted that this turbo was not laggy at all and gave excellent response.

If your sure that 250rwkw is all you want, then thats the road i would take.

Your best bet is ring UAS, they told me theyve sold, installed, and tuned many of these recently on R33's. Tried and tested, easiest way to go!

[CroatianR33]

So would i just need one of those Bosch 044 Pumps? Would a Power Fc be fine for this type of power output or should I go for a microtech?

I would definitely be getting a FMIC and full turbo-back 3" exhaust. I heard about a special High-flowing job that GCG or was is CGC, do for the standard turbo to help it reach or get very close to my goal. Would that be a good option?

[CroatianR33]

Whats the difference between internal and external gates?

[Guest Robo's]

Where is UAS?

[paulr33]

uas is in sydney - see nismo.com.au thats them

check out:

turbo specs page: http://www.ooparts-international.co.jp/frameset.html

turbo specs page (in ps rating): http://www.driftcentral.com/content_turboi...hp?tinfo=ttable

220-240rwkw: http://www.skylinesaustralia.com/forums/sh...ight=power+rwkw

230rwkw: http://www.skylinesaustralia.com/forums/sh...ight=power+2530

[paulr33]

read the 2nd post of (220-240rwkw) which is what sydneykid lists what you need for a 220-240rwkw config

[Chef_32]

Don't forget to upgrade suspension, brakes, and tyres to suit.

[benm]

I'm on the road to 250rwkw myself and this is what i'm doing...

Currently:

* Std ECU

* Std Turbo

* Std Injectors

* Ex Cam Gear

* 3" Turbo Back Exhaust

* Dualstage Boost Controller

* K&N Panel Filter

* FMIC

* Clutch

* Bosch 040 Fuel Pump

= 186rwkw (rich)

Future:

* Power FC + H/C + Boost Kit ($1900)

* GCG 500hp Hiflow Turbo ($1900)

* Fuel Pressure Regulator ($160)

= 240-250rwkw (leaned out and with a bit of luck)

By the time I get there i'll need a better clutch and also some wider rims so it never ends. Now I just gotta find about $5k

[CroatianR33]

OK guys. Now all I have to do is SAVE!!!

[gobiz]

What do you know, I'm on the road to 250rwkw (maybe even a bit more)

I've got FMIC 600x300x100,Decatted exhaust + pod with CAI.

This is what I'm going to do:

T3/t4 hybrid turbo, int. gated rated 500hp bolt on

Haltech E6X full management

Bosch pump 044 if 910 doesn't do the job(i've already gotten the 910)

550 injectors

Fuel pressure reg.