Jump to content
SAU Community

Recommended Posts

Just trying to understand how much am I losing, gaining, if I go with ATTKD instead of DBA 5000's - my original rotors are warped, and I might as well go the 2-piece route.

ATTKD 2-piece ones are $499

(+shipping) on justjap site, presume for a set, and DBA's are quite a few $ more.

Are DBA 5000's worth the extra money.

Is it hard to find replacement parts for ATTKD's? DBA replacement parts are fairly easy to find.

Any feedback would be great.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/379506-attkd-vs-dba5000/
Share on other sites

I'd be grabbing the ATTKD over the 5000's. Something to think about is the new DBA4000 design, iirc they will be around the same price as the ATTKD and can't see them being any better.

So I'd get the ATTKD.

I'm using the ATTKD / KSPORT / G4 / D2 330mm rotor

What are you using the car for??

If it's predominately a street driven car go with an ordinary single piece rotor. Under your foot your not going to notice any difference from a base model RDA to a 5000 series DBA.

Well, I'm basically using it to fill the empty space in the garage, but I do a track day or two. Hoping to do all the SAU-Vic rounds next year, so could see some use for the 5000's, otherwise I'd go for the 4000's.

I'd be grabbing the ATTKD over the 5000's. Something to think about is the new DBA4000 design, iirc they will be around the same price as the ATTKD and can't see them being any better.

So I'd get the ATTKD.

I'm using the ATTKD / KSPORT / G4 / D2 330mm rotor

Thanks for the advice John, considering the pace you do guess those ATTKD's are not bad at all then!!!

I recently converted my front end brakes to ATTKD 8 spots & 356mm rotors & can't fault them what so ever . Great on the road , great on the track with no break fade what so ever . For the price i think they are great value for money :)

Well, I'm basically using it to fill the empty space in the garage, but I do a track day or two. Hoping to do all the SAU-Vic rounds next year, so could see some use for the 5000's, otherwise I'd go for the 4000's.

If you do end up deciding to just go the 4000 series, we've got 9 pairs of front slotted to suit in stock that we're doing on special at the moment, $184.80 per rotor.

I recently converted my front end brakes to ATTKD 8 spots & 356mm rotors & can't fault them what so ever . Great on the road , great on the track with no break fade what so ever . For the price i think they are great value for money :)

need 18's for that setup - otherwise I could run them in the future.

need 18's for that setup - otherwise I could run them in the future.

I have 19's on mine , so i have no problems with clearance . Your right though 18 are the minimum with the 356mm rotors :) I have the Attkd 8 spots up front , with standard 2 spots at rear with Dba t slot rotors & project mu pads. Also got braided lines all way round , cusco master cylinder stopper & Motul Rbf 600 brake fluid . This setup is fantastic & have no brake issues what so ever !

Well, I ended up getting a set of ATTKD's 2 piece rotors, DBA mucked me around a bit, took more then 3 weeks since I put an order in and they still couldn't tell me if and when I'll receive them so I cancelled the order...................but funny thing happened with my original rotors - they don't feel warped any more, even when I brake really hard they feel smooth just like before. hmmm, funny that ey, so I decided to leave them on the car for a while and I'll swap to those ATTKD's later - its not bad having a spare set of rotors on the bench.

You guys reckon they'll just warp as soon as they get hot again or they may be ok for a while longer?

Damn, I didn't knew about these... let say, I start learning how to lap next year, would the DBA 4000 still be fine or should I go ATTK right away?

Anyone tried the AMS rotor?

http://forums.gtrcanada.com/ams-absolute-motor-specialties-inc/42748-ams-max-slot-16-r32-2-pc-front-rotors-intro-sale-%24399.html

Damn, I didn't knew about these... let say, I start learning how to lap next year, would the DBA 4000 still be fine or should I go ATTK right away?

Anyone tried the AMS rotor?

http://forums.gtrcan...ale-%24399.html

I would keep the original rotors on, until they crack or warp, and just fit the car with good brake pads, and really good brake fluids. Your old discs are probably very good, they would have gone through the heat cycle many times and will be better then some brand single piece disc.

I used original rotors with DS2500 and RBF600.

was also looking at the comparison as i hae the DBA5000's on atm and considered the difference against the ATTKD branded ones. have spoken to Justjap and theyve told me its technically same as the D2/k-sport/taiwanese-made gear, just with a japanese company branding on it with the workshop's consent.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Ha ha, ended up going it alone.  I just sent it (in a very nervous fashion).  Once I'd released the locks and it didn't automatically start spinning out of control i felt a bit more confident.   It made some loud sounds (cracking and creaking noises) when I first spun it which got the heart rate going again!  I couldn't bring myself to leave it tipped on the side.  I feel a bit more comfortable having back right side up while it sits there. I'd get angry with your last point but you're 100% correct! 馃槄 Even yesterday I managed to distract myself at numerous times to make a bracket to fit an LED flood light off the back of the house and fix my sons pushbike.  There were other little taks nibbling at my brain for the rest of the day too...
    • Probably one of the more nerve wracking experiences of my entire life! 馃槀馃槀 The balance (centre of gravity) is out still but in a direction that gives me comfort!   It's quite bottom heavy still meaning it takes a bit of muscle to rotate it.  The plus side of that is that it wants to to go back to upright.  Better that than wanting to go all stranded turtle on me!
    • hmmm that's not ideal. This is a pretty new engine right, will be interesting if your engine guy has any theories about causes
    • A universal ball joint removal c press kit is better money spent and will work for the Hicas ball joints.  Here's a 45$ CAD Example. ATPEAM Heavy Duty Ball Joint Press Kit with 4WD Adapters | Professional 4 in 1 Ball Joint Press Removal and Installation Tool for Cars and Trucks | Universal Ball Joint Tool with Storage Case, Ball Joint & Tie Rod Tools - Amazon Canada
    • True on both points
  • Create New...