Jump to content
SAU Community

Recommended Posts

I did the please respond troll to an ex the other day, she didn't acknowledge it once out of the 5 or 6 times I said it = probably now thinks I'm legitimately desperate for replies to messages :(

still cant believe i won the $300 track day!

Fuu**kk You!!!! I'm so jelly

what please respond?

Have a read of the last few pages of the lulz thread theres a link to a troll thread to the BB forum.

hahahaha the refreshing sunkist will be at show and shine.. im going to cruise up with you so i can definitely get a spot. im just gonna go to work if i get bored.. lol its down the road.

hey if you sell your weels let me know.

no it says in your sig that you want TE37.

you wish I was dreaming about you gupta

OH YA!!! forgot about tht...itll have to wait until next year now...that money i had went to repair couple of investment houses i have :( .... back to square root of saving up for my car :)

OH YA!!! forgot about tht...itll have to wait until next year now...that money i had went to repair couple of investment houses i have :( .... back to square root of saving up for my car :)

all good bud. let me know when you sell em, i'll buy them off you as track wheels.

The French are a inferior beta bunch having had their arses handed over to them in a silver platter by the Germans plenty of times in history.

in 1870, 1914 and 1940 lulz..

insert facepalm here

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...