Jump to content
SAU Community

Recommended Posts

Why does it sound like a tractor and have such a high pitched spool? Lol

Deff gasket is gone somewhere.

Hrmm.. Unless you break Moh's legs he might edge you out and get the Show n Shine this year!

Speak for yourself. I've already had two final inspection days this year :P

Get a discount for being a SAU VIC member?

If not you can buy me a Thai Chicken Curry at the next GC meet for the monies saved :P

Hrmm.. Unless you break Moh's legs he might edge you out and get the Show n Shine this year!

Haha, I'm going 6yrs straight now. Lets see if his survives the time haha

Get a discount for being a SAU VIC member?

If not you can buy me a Thai Chicken Curry at the next GC meet for the monies saved :P

Wasn't aware we had discounts at final inspection?

Isn't your job detailing cars? You should be able to do your car easy!

Doesn't need to be clean at all. Only clean ones from wastelands might be Aaron and Adam

Everyone else might be rocking up with dirty cars :P

When isn't my car clean. Even when it's dirty it's clean. I never understand

Isn't your job detailing cars? You should be able to do your car easy!

Doesn't need to be clean at all. Only clean ones from wastelands might be Aaron and Adam

Everyone else might be rocking up with dirty cars :P

Lol Ex Detailer!

I used to use all Hondas things to detail my own car, I don't own a buffer, well one which works :/

Might need to try grab one before then

lol sadly :(

im just going to leave them and get a guy who does full wheel restorations to do them in a month or two

they are all awesome condition especially the rears, its just front left which has some clear gone lol

also nothing will take the brake dust off lol

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • What can't be done with a little bit of decking board or similar timber bolted to a hub flange via 2 wheel nuts is not worth talking about.
    • I noticed something. On the tps sensor and the sensor behind the adjustment screw is adjusted towards the far left. Are these screws supposed to be centered? (this sensor was in the same position before the tune as well)  Also attached a photo of where my car usually idles at when warm (sometimes a tiny bit above that). I think I might have screwed up the calculation and it might have better than I thought lol at 750rpm still not 650rpm though.      
    • So for both general interest of engine health, and to rule out any coolant/oil issues, I organised an oil analysis done on the 125,000klm oil Results below, all good, just a bit of fuel dilution which I'm not too worried about
    • This is actually a really good way of measuring what wheels fit. If only there was a similar measurement between hub face and suspension :p That said, it's probably pretty simple to actually measure it all with the wheel off the car for the rear. The front is a bit more complex but.. 
    • Being the top Google search result for R34 wheel-related inquiries, lemme throw down my experience. I calculated that 100mm from hub face to wheel face is about the perfect fitment for my ENR34 sedan.  I've been running 18x8.5s, ET35, with a 1" spacer. So, 8.5in to mm = 216mm. 216/2 = 108mm. 108-35 = 73mm. 73+ 25 (1" to mm) = 98mm.  If you wanna get close to this on dif widths, here are the offsets you'll want: 9" - ET around 15mm 9.5" - ET around 20mm 10" - you're crazy, but ET around 30mm All these should fit perfectly on a non-widebody, non-GTR Skyline. Note that it's probably the absolute max, and you're probably better off running a couple degrees of camber in this config, but it looks great, super flush.
×
×
  • Create New...