Jump to content
SAU Community

Recommended Posts

Different cruise brah....

Am aware...but just talking about the spur or any roads up there reminds me of him.

I'm convinced he was a professional troll. There's no way someone could be that stupid / that much of a douchebag / that much of a stalker. And the wheel swap confirms it.

inb4 he converts the front end to an R33

Someone buy it or at least read the ad; I put a lot of effort into the sales pitch

http://www.skylinesaustralia.com/forums/topic/423621-fs-apexi-power-intake-pod-filter/

Am aware...but just talking about the spur or any roads up there reminds me of him.

I'm convinced he was a professional troll. There's no way someone could be that stupid / that much of a douchebag / that much of a stalker. And the wheel swap confirms it.

inb4 he converts the front end to an R33

no way he's a troll man... I wish I could tell myself he was... I would sleep easier at night knowing he wasn't out there

Someone buy it or at least read the ad; I put a lot of effort into the sales pitch

http://www.skylinesaustralia.com/forums/topic/423621-fs-apexi-power-intake-pod-filter/

wow!

5-7k. Not looking for anything flash. Just has to have 3 pedals

pulsar?

I should become the Pulsar Used Car Salesman here... trying to convince other people to advertise their cars on here because lots of people avoid carsales/gumtree for many reasons and no one on PGA buys cars.

Stalker Stoppers International

4 February

"PLEASE NOTE"

"This Business is Under Construction Until Further Notice & is Not open for Business at this time"

I APOLOGIZE FOR ANY INCONVENIENCE.

If you have a stalker of your own & if you have any questions regarding your safety please post a question on this page & I will endeavour to try to give you advise or hits on how to help keep yourself safe from stalkers until we are open for business to help you more directly.

"THIS ADVISE IS FREE OF CHARGE"

Thank You for Your patients at this time.

I'm guessing he calls his victim's "Patients"

lol I remember him setting up that page. That was probably the scariest thing he did IMO...it was like a dumb criminal trying to set up the "perfect" alibi. He couldnt be a stalker, he's from stalker stoppers! That made me think he was properly harmful.

we are talking about a guy that thinks paris hilton is going to visit his house in benalla and says goodnight to alyssa milano via twitter EVERY NIGHT...

then there was the spotted thread saga...

def not troll

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...