Jump to content
SAU Community

Recommended Posts

housemates are annoying.

My housemate went through 9 knives yesterday. All are sitting in the dishwasher, doesnt wash any of them so that everybody has knives to use the next day or day after. She single handedly fills the dishwasher in 2-3 days. Apparently she eats something every 2 hours and that requires plate, cutlery, cup etc. I dont know where she has the time to go to uni as well as use up the entire contents of the cupboards. She basically lives off hard boiled eggs and sometimes leaves shell fragments on the counters. ergh. She leaves at the end of June thank christ... but then I'm left with the entire rent. In April she started complaining about how could the house was in April, because Swedish houses are double insulated with triple layered glass. pfft, 15 degrees in house is not cold.

So car runs in that pic... why car no run now?

as it went into ford for new starter, (the old one died on the street outside when looking at dailys, and came back a 61/2 cylinder.

then we got drunk and build getting out of control

My housemate went through 9 knives yesterday. All are sitting in the dishwasher, doesnt wash any of them so that everybody has knives to use the next day or day after. She single handedly fills the dishwasher in 2-3 days. Apparently she eats something every 2 hours and that requires plate, cutlery, cup etc. I dont know where she has the time to go to uni as well as use up the entire contents of the cupboards. She basically lives off hard boiled eggs and sometimes leaves shell fragments on the counters. ergh. She leaves at the end of June thank christ... but then I'm left with the entire rent. In April she started complaining about how could the house was in April, because Swedish houses are double insulated with triple layered glass. pfft, 15 degrees in house is not cold.

by 9 knives?

did you mean steak knives? or like kitchen cutting knives?

Why would you need steak knives on a regular basis? and why would you need 9 different kitchen knives? (i only have 6)

just normal cerated knives, ontop of the 2-3 kitchen cutting knives. Even if I was home all day, wouldnt probably go through like 3 max. and if i did, I would wash them with the non-dishwasher compliant stuff so there are at least some clean knives for others to use.

So about $200 to $300K once he gets a few years experience lol

probably in about a decade.

but yeah, the biggest hurdle, to be honest, is landing a good job in the first place, once you're in, you're probably set. and i put a lot of effort into work, but not as much effort when it comes to studies. Results show that effort, but employers always have good things to say, though its all hospitality, waitering and cook and stuff, so really irrelevant.

Am trying to get into my metallurgy lecturer's good books at the moment, so he'll be a reference for my resume, having one of the top metallurgical profs as my reference should do wonders.

just normal cerated knives, ontop of the 2-3 kitchen cutting knives. Even if I was home all day, wouldnt probably go through like 3 max. and if i did, I would wash them with the non-dishwasher compliant stuff so there are at least some clean knives for others to use.

I have 15 sets of chopsticks, i only use 2 sets. the same two sets day after day.

Washed of course. And i've never really understood using the dishwasher, if you're eating for one, its quite difficult to generate enough dishes to fill up the dishwasher, and while you're waiting for the dishwasher to fill, the food bits start going bad, in the slightly warmer dishwasher, and that's probably not the best thing to happen.

I have 15 sets of chopsticks, i only use 2 sets. the same two sets day after day.

Washed of course. And i've never really understood using the dishwasher, if you're eating for one, its quite difficult to generate enough dishes to fill up the dishwasher, and while you're waiting for the dishwasher to fill, the food bits start going bad, in the slightly warmer dishwasher, and that's probably not the best thing to happen.

exactly. this is the first rental ive lived in with a dishwasher, and it used to rarely get used since i was so used to doing dishes. oh well...

hey, dast ist mein hamburger

Been to the "meat and wine co" in hawthorn? What did u think if u have?

no... have not...

I shall look at the menu online now and tell you why i hate it though

hoax

all steakhouses call themselved "the best in melbourne" :P

had a look and it doens't look too bad, however for the prices you could do better.

if you are looking for about that pricerange, go to Bistro Vue

http://www.vuedemonde.com.au/bistro_vue

will be at least 10,000 times better than M&W Co

Well where do u think is good rare steak for under about $60 a main?

Meat n wine co is supposedly meant to be "the best in Melbourne"

I've been to meat wine & co in the city

Had a waygu steak

It wasn't that great to be honest

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Um. No. Since Matt introduced the TIM it has become a lot easier to deal with the consequences of changing K for AFM and injector swaps. Then, tuning is a f**king doddle. No-one needs to know or care how many grams of air are flowing or any other bullshit. Need more fuel in a cell? Add more fuel. Need more timing in a cell. Add more timing. Need to adjust any of the other tables for warm up and so on? No harder than anything else. Sure - it's not an ECU system for starting from scratch on an arbitrary engine. But then.....it was never supposed to be, not recommended for, and almost never used that way. So.... On your engine, in particular, Nistune/Nissan OEM is about as sophisticated and difficult as banging 2 rocks together. Those ECUs are primitive and simple. There is nothing difficult there. I learnt Nistune from scratch, created new maps with extended axes, interpolated/extrapolated the original maps onto them and tuned my RB20 (basically the same ECU as your 26 ECU) all by myself, more than 20 years ago. And that was long before even TIM.
    • Set of knee pads for a R34. Will fit every model I think. Comes with everything except the rubber covers for the bolt holes. Still in great condition. You will need to drill holes to mount these or use double sided tape. I can do free shipping and will be shipping from the Netherlands with tracking.
    • Nistune needs something like an entire excel spreadsheet in which you build an abstraction layer that converts everything from real units you can actually measure into all of the various tables. The number of unexpected dependencies hiding in how the Nissan ECUs do math is a pretty impressive optimization trick for 8-bit MCUs but good god is it awful to actually work with in practice. 
×
×
  • Create New...