Jump to content
SAU Community

Recommended Posts

hahaha, messed up. you wouldnt see it on a chocolate one :ph34r:

A45 AMG tried to drag me on beach road tonight...

Soon.jpg

in other news:
http://theshovel.com.au/2013/12/15/abc-comes-clean-mr-squiggle-was-a-puppet/

called vicroads a while ago asking what hoops needed to jump through the change engine number on already-engineered vehicle. said just bring a letter from mechanic with details and signature and youre good to go. sweet.

rock-up, fill in the form, lady checks the new engine number isnt from a stolen vehicle, all good. "where have you parked the car?" "err its not here" "we need to inspect it" *sigh*

Sure enough the website says you need to show the physical engine number. ma bad

fingers crossed they keep any thoughts on road-worthiness to themselves and just focus on engine number.

Anyone else feel like beating down on that guy on Driftsales that sells the "ADR approved" fake brides and takata harnesses?

riccy something yea. wadda kent.

bloke asks him are they adr aprroved mate?

he says.

they have adr tags.

so many kids are gonna get ripped off.

riccy something yea. wadda kent.

bloke asks him are they adr aprroved mate?

he says.

they have adr tags.

so many kids are gonna get ripped off.

Rocky Siciliano or similar

Every time he posts stuff up he says "Bride fixedback seats" ADR approved $650 pair

then someone will ask if they are copies and he will say yes - but they are better as they are adr approved

heaps of people cracked it and now he is saying "they have ADR tags"

fkn scumbag

Rocky Siciliano or similar

Every time he posts stuff up he says "Bride fixedback seats" ADR approved $650 pair

then someone will ask if they are copies and he will say yes - but they are better as they are adr approved

heaps of people cracked it and now he is saying "they have ADR tags"

fkn scumbag

thats the kent. also sells rip off wheels for 90 bucks. momo etc.

FIEND!

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...