Jump to content
SAU Community

Vic Wasteland Thread


R31Nismoid

Recommended Posts

just bare in mind here fellas, the gps hardware shit you use on your phone, is a once calibrated piece of junk.

use a seperate designed for piece of equipmunk, and make sure its calibrated.

also, enviroment plays a huge part in gps signal. so dont just rely on that.

not saying whats above is wrong, just giving you all the info.

Link to comment
Share on other sites

don;t use the gpn on the phone,

I use an external 10Hz GPS reciver liked to racechrono on android.

the lap times are withing .1 of a second of the track ones, (think it more due to the start stop line in racechrono is not the same as the beam they use for our track days)

so think the results are fairly accurate.

Link to comment
Share on other sites

assumed that but thought would clarify.

when I used the GPS jsut on the phone times were more than a sec out from lap times, the external GPS as mentioned brought it down to sub .1 so I'm happy for the time being.

  • Like 1
Link to comment
Share on other sites

If you need to be accurate to less than 1/10 of a second for recreational racing... you need to get a life lol

If you want an accurate representation of how well a different line through a corner effects your time, then having an accurate GPS is pretty important.

I use a 10Hz Bluetooth module as well, stuck to the top of my windscreen, because I have my phone wrapped up in my centre console and GPS Reception when you're inside a big metal cage isn't ideal.

Lap times can be within a 0.1 seconds... however things like top speeds and corner speeds go absolutely retarded if you've got a poor signal and it thinks your bouncing all over the track.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...