Jump to content
SAU Community

Recommended Posts

It's ok to be judged within reason..

But riced up car no thanks

If I was still in sales, I'd rather no judgement from them until I had sussed them out and then I could talk about my other car etc. if I saw that they might be into that.

But yeah riced up cars do you no favours unless you work in that industry or for Autobarn.

Saw a real estate agent rock up in a riced-up rx8 :/

Lol when we had our Track Day tech night the other month the pizza delivery dude rocks up in an RX8 with 40 pizzas... Saw it was a car type event, gave it a rev coming up the driveway... we lold in pity

  • Like 1

guy who delivered our pizzas for the last tech night was in a very riced very thrashed RX8

He thought he was so cool hitting the limiter when leaving..

(he did deliver 30 pizzas so if it was 5$ a pizza he would have been in a good mood anyhow)

Yeah so it could be 2 could be 10 pizzas, typically you get to know the 'good tipping addresses' and race there as fast as you can so you get a good tip.

I remember this one guy, used to always pay with $50 and say 'keep the change' for like 1 pizza and a drink, baller probably in dezz's line of work

Edited by UNR33L
  • Like 1

While you were all at uni for a piece of paper, I was busy making paper.

i'm guessing you were an apprentice when other at uni, and from what I knew of tried apprenticeships straight out of school sucked massively.

best mate was a motor mechanic, 5200 a year first year.

another mate was an apprentice elect , around the samepay till hit 18, improved a bit,

but at 20 finished apprenticeship moved to perth and was on 120K doing work at the mines.

FIFO plus Union, PLUS explosives danger money...

(he was doing the electrical systems for the explosives carts in the mines)

where as his wife did uni, got degree, now a lawyer earning shit loads more than him...

  • Like 1

I finished school in 2003, didn't start my apprenticeship til 8 years later.

I'm not saying no one should go to uni or whatever, but most of the people that use the example you used above, forget to factor in the money they weren't making for the ~4 years they were at uni, so unless they're on mega bucks when they do get out, they won't be catching up/overtaking those who worked from the get go anytime soon.

Of course money isn't everything for some people, so it's not much of an argument, but for materialistic mother f**kers like me, it's pretty much everything

  • Like 1

i'm guessing you were an apprentice when other at uni, and from what I knew of tried apprenticeships straight out of school sucked massively.

best mate was a motor mechanic, 5200 a year first year.

another mate was an apprentice elect , around the samepay till hit 18, improved a bit,

but at 20 finished apprenticeship moved to perth and was on 120K doing work at the mines.

FIFO plus Union, PLUS explosives danger money...

(he was doing the electrical systems for the explosives carts in the mines)

where as his wife did uni, got degree, now a lawyer earning shit loads more than him...

But most people don't do law degrees and most lawyers don't even end up making truck loads

I cracked well over 6 figures at 21 never looked back

I finished school in 2003, didn't start my apprenticeship til 8 years later.

I'm not saying no one should go to uni or whatever, but most of the people that use the example you used above, forget to factor in the money they weren't making for the ~4 years they were at uni, so unless they're on mega bucks when they do get out, they won't be catching up/overtaking those who worked from the get go anytime soon.

Of course money isn't everything for some people, so it's not much of an argument, but for materialistic mother f**kers like me, it's pretty much everything

when I tried uni most were on ausstudy earning 200+ per week...so they were surviving fine for that 4 years.

Uni wasn't for me however, was sick of school no idea on what I wanted to be doing in 6 months even less for rest of my life, so got out and tried some stuff.

took this job thinking it would be fun for 12 months or so and now worked here for just under 15 years.

But most people don't do law degrees and most lawyers don't even end up making truck loads

I cracked well over 6 figures at 21 never looked back

very true but not every Tradie does as well,

all comes down to drive and how much your willing to learn.

Still got plenty of friend from high school who did their apprenticeship, stayed in the country and happy to work from some-one.

so long as they can pay off their 150K (or less) home loan and afford a woodstock or UDL on friday they happy.

for every-one doing good there some just getting by and happy with their lot.

when I tried uni most were on ausstudy earning 200+ per week...so they were surviving fine for that 4 years.

Uni wasn't for me however, was sick of school no idea on what I wanted to be doing in 6 months even less for rest of my life, so got out and tried some stuff.

took this job thinking it would be fun for 12 months or so and now worked here for just under 15 years.

Big difference between survivng and doing well. $200 a week, $10k a year... I spent that on the engine alone in the R33

Like I said, not everyone is all about the money, that's fine. It's only funny when people with degrees/diplomas etc look down on tradies etc

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • You're not wrong, but more than a few times I've heard of people running into issues where their injector characterization isn't quite right and that approach works for that specific configuration but once they switch over to a new set they discover a whole bunch of stuff wasn't set up correctly. It's slightly more annoying to reverse engineer the OEM MAF transfer function but you already have the sensor wired up to the factory harness so keeping it around for a few weeks more while you figure out the tune is easy enough. I've seen GM also use a combination of both MAF + MAP in their ECUs before, MAF is for steady state and a calculation of the cylinder VE to correct the base VE table, then in transients it uses that calculated VE + raw MAP to determine cylinder filling somehow.
    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
×
×
  • Create New...