Jump to content
SAU Community

Vic Wasteland Thread


R31Nismoid

Recommended Posts

The world will slowly but surely gravitate towards the dystopian future depicted in Equilibrium...tis only a matter of time and the reason we won't be scared of it is because it'll be such a slow, drawn out process.

The scary thing is that that movie is less a vision of a potential future and more an analogy of what we already do as a society - popping pills to keep emotions in check, censoring art and opinion, restricting choice and seeking out and destroying anything that threatens this.

/orwellianparanoid

Link to comment
Share on other sites

Am curious if multinational organisation would sue poverty stricken child with Facebook provided internet access out of principle

FB armchair / feel good activists en masse

Link to comment
Share on other sites

Define seed though....

Is that for while you are downloading or only if you don't stop it afterwards?

Seeding vs Leeching is only a term to distinguish between connected and sharing pieces, and connected to the tracker with 100% of the pieces...

You're guilty the moment you connect to the tracker, because you can't connect without SOME of the file (included in the initial .torrent file)

Link to comment
Share on other sites

Define seed though....

Is that for while you are downloading or only if you don't stop it afterwards?

I mean after it's done

I foolishly didn't bank on Simon the IT nerd coming in to ruin my joke lol

  • Like 1
Link to comment
Share on other sites

That's what i mean. I could download a movie and stop my client/delete the file the second it is finished and they could still say i seeded it...

Or do they look into if further and focus on people who seed long term?

But aren't you seeding while you're downloading? Hence the uploads. Or is that defined as a different term?

Link to comment
Share on other sites

It may, or may not though.

Seeders, in general would have 100% of the file, and are sharing 100% of the file, and you could arguably identify and say that you're illegally providing/distributing the file for others, once you have 100% of an item.

It makes it a bit easier to go after seeders, legally, due to that.

Link to comment
Share on other sites

It may, or may not though.

Seeders, in general would have 100% of the file, and are sharing 100% of the file, and you could arguably identify and say that you're illegally providing/distributing the file for others, once you have 100% of an item.

It makes it a bit easier to go after seeders, legally, due to that.

Yeah, but you are always seeding when you have 100% of a file... even if it's just for 1 second before you stop it.

my point is will they go after THOSE people...

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yeah most people that have heard it said it was fine but it's always had me slightly worried. Oil pressure I can't remember off the top of my head but it has plenty, I run 10w60 You're probably right mate, best get ordering some shims! Guessing Nissan is the best place for them?
    • Just wanna preface this and point out I'm a mechanical fitter by trade but have had very little rebuild/machining experience, but I am keen to learn, hence this project. Bit of a write up here so bear with me, just want to make sure I do this right  I've got an rb30e currently pulled down. Planning on putting a 25 head on it and running it in my s14.  Not chasing huge power so I'm just going to try get away with factory bottom end for now.  Started measuring the crank the other day, realised my budget daytona micrometer set wasn't up to the task (surprise, I know). They only measure to 0.01mm but the Nissan specs are to 0.001mm. Anyway, I started measuring anyway and came away with the mains being inline with the oem spec, as well as the big ends, except for no. 5. I consistently got a measurement of a hair over 49.96mm, where all the others were pretty spot on 49.97mm. The lower spec for grade no.1 is 49.961mm. I'm getting access to some better gear my next days off to double check everything, but in the case that the big end is right on that bottom spec, is it pretty much just a case of straight to the machine shop for machining and oversized bearings? I understand I need to measure the tunnel as well to work out my oil clearance, but it's the different grade bearings in the manual that are confusing me. What is generally the process when one journal would still technically be in spec, but in a different grade?  Thanks for coming to my Ted talk
    • You need to visit Ipswich. Plenty of clapped out R32 and R33s running around here as daily drivers. And when I say clapped out, they're how you'd look at a VN, when it's the year 2010...
    • So I checked this out in the weekend.. and look at this. I remember watching the videos. Finally got to see it in person! BRB. Tissues. Got tonnes of other pics and videos too.      IMG_0171.mov IMG_0113.mov
    • For anyone who might be put off by the slightly wacky wheel offset shown on the box photo above, the production models are not like that. Here's some more pics of the actual product (as well as the interior)
×
×
  • Create New...