Jump to content
SAU Community

Vic Wasteland Thread


R31Nismoid

Recommended Posts

They'll get him on trespassing and possession of stolen police property once they extract the bullet from his head...

you forgot defacement of public properly as there blood on the bullet.

Link to comment
Share on other sites

One man said the car was three metres from the policeman, on the opposite side of the road, at the time the shots were fired.

‘‘It [the shot] blew out his tyre and they [the occupants] bailed on foot,’’ he said.

interesting...

pretty much the opposite of what the police have said

Link to comment
Share on other sites

interesting...

pretty much the opposite of what the police have said

intradasting

If this is the case, then firing his weapon is definitely not required, if he could have simply turned his head and written down the number plate of the offending car and popped around for a followup visit later on that night...

Mate of mine used to be a cop, said to us on multiple occasions that the ONLY time that they were allowed to fire their weapon was if someone was about to be killed or seriously injured and it was the only way that it could be stopped.

Link to comment
Share on other sites

http://au.news.yahoo...-too-often-lay/

Hahaha he shot at a shitty old Nissan R31 wagon? What was his life endagered by? an RB30 iron block dropping on his leg? Rust? Boredom?

Also wow talk about deflecting the situation - they found bullets in a carpark nearby in the morning... so they've made the assumption that last night the police weren't the only ones there with guns.

Link to comment
Share on other sites

"Victoria's police chief says he's worried about how often his officers are shooting at fleeing drivers after another incident in which a policeman shot at a car in Melbourne."

6 times in 12 months... Doesn't sound like it's the absolute last resort to me...

Link to comment
Share on other sites

Would of been awesome if one of the car 'hoons' that apparently brought a gun shot the officer.. bloody cops

Just shot in the dick or something, that would teach them a lesson.

Edited by UNR33L
Link to comment
Share on other sites

Would of been awesome if one of the car 'hoons' that apparently brought a gun shot the officer.. bloody cops

Just shot in the dick or something, that would teach them a lesson.

"You defect one more vehicle and I'm cutting your dick off" lol

Link to comment
Share on other sites

should have called brah. always free to rescue, unless i'm at work. i live near the bwd hwy/middleborough road intersection

Will note for next time. Cheers brah.

If I'm not running for my life while being shot at anyway. M I rite.

Edited by kaitoukid
Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Wait, the flappy paddles or sequential is the small penis indicator?  Either way, I can't afford it.
    • You and me both. If I ever get it running again, I'll have to look into cruise control.
    • Yeah most people that have heard it said it was fine but it's always had me slightly worried. Oil pressure I can't remember off the top of my head but it has plenty, I run 10w60 You're probably right mate, best get ordering some shims! Guessing Nissan is the best place for them?
    • Just wanna preface this and point out I'm a mechanical fitter by trade but have had very little rebuild/machining experience, but I am keen to learn, hence this project. Bit of a write up here so bear with me, just want to make sure I do this right  I've got an rb30e currently pulled down. Planning on putting a 25 head on it and running it in my s14.  Not chasing huge power so I'm just going to try get away with factory bottom end for now.  Started measuring the crank the other day, realised my budget daytona micrometer set wasn't up to the task (surprise, I know). They only measure to 0.01mm but the Nissan specs are to 0.001mm. Anyway, I started measuring anyway and came away with the mains being inline with the oem spec, as well as the big ends, except for no. 5. I consistently got a measurement of a hair over 49.96mm, where all the others were pretty spot on 49.97mm. The lower spec for grade no.1 is 49.961mm. I'm getting access to some better gear my next days off to double check everything, but in the case that the big end is right on that bottom spec, is it pretty much just a case of straight to the machine shop for machining and oversized bearings? I understand I need to measure the tunnel as well to work out my oil clearance, but it's the different grade bearings in the manual that are confusing me. What is generally the process when one journal would still technically be in spec, but in a different grade?  Thanks for coming to my Ted talk
    • You need to visit Ipswich. Plenty of clapped out R32 and R33s running around here as daily drivers. And when I say clapped out, they're how you'd look at a VN, when it's the year 2010...
×
×
  • Create New...