Jump to content
SAU Community

Vic Wasteland Thread


R31Nismoid

Recommended Posts

correction, work in springvale, i should be more afraid of knives.

dem se skidz stahp for no one brah... in front of knox, yolo and all that.

in a lot of ways, a knife wound is a lot scarier than a gunshot wound, though i assume we're talking small arms here.

get hit by an assault rifle round and there is no way in hell you're coming out a non cripple.

5.56/7.62

Link to comment
Share on other sites

in a lot of ways, a knife wound is a lot scarier than a gunshot wound, though i assume we're talking small arms here.

get hit by an assault rifle round and there is no way in hell you're coming out a non cripple.

5.56/7.62

Unless you're talking .22 versus machete, I'll take the knife wound.

Link to comment
Share on other sites

6 inch knife wound is pretty fatal or paralysing anywhere on torso...it's also a bigger wound...you can get lucky with being shot as long as it misses vitals. .38 is still a sizable slug though, good chance you're dying fast without hospital attention :(

I'll take the gun shot to the torso and the knife wound to the limbs/head assuming they don't have the strength to go through bone. Need to ask my paramedic mate as I'm sure he's seen both in his time.

Link to comment
Share on other sites

mrs was upset I wasn't gonna be home till late. she wanted to cook dinner for a change. srsly you can do it any other day of the week. I said I'd buy her a rose, but not till next week. shit is daylight robbery.

Hallmark men and women. scourges

park on lygon st is full of roses...

jus sayin

Link to comment
Share on other sites

Whats making you go crazy?

Im just taking my missus out to dinner and that's it. Maybe buy her 1 rose or something

lol, nah. I'm not going crazy. Was referring to all these knife and bullet to the head preference.....

I too, just taking mine to dinner. Trying to think which neighbour's garden shall be my victim this year for a rose/flower. hahahaha

park on lygon st is full of roses...

Those people that walk around sell roses..... my gosh, comes up towards ya all happy and cheerful and when i say no to their $40/rose sale they get moody.

Link to comment
Share on other sites

booked Huxtable for dinner tonight....

First Valentines day ever that I have sat in a restaurant and not worked lol!

I dont beleive in it but it's good to make it up to her as all the previous V'days consisted for her being home alone and me coming home at 1am in a FOUL mood lol

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Wait, the flappy paddles or sequential is the small penis indicator?  Either way, I can't afford it.
    • You and me both. If I ever get it running again, I'll have to look into cruise control.
    • Yeah most people that have heard it said it was fine but it's always had me slightly worried. Oil pressure I can't remember off the top of my head but it has plenty, I run 10w60 You're probably right mate, best get ordering some shims! Guessing Nissan is the best place for them?
    • Just wanna preface this and point out I'm a mechanical fitter by trade but have had very little rebuild/machining experience, but I am keen to learn, hence this project. Bit of a write up here so bear with me, just want to make sure I do this right  I've got an rb30e currently pulled down. Planning on putting a 25 head on it and running it in my s14.  Not chasing huge power so I'm just going to try get away with factory bottom end for now.  Started measuring the crank the other day, realised my budget daytona micrometer set wasn't up to the task (surprise, I know). They only measure to 0.01mm but the Nissan specs are to 0.001mm. Anyway, I started measuring anyway and came away with the mains being inline with the oem spec, as well as the big ends, except for no. 5. I consistently got a measurement of a hair over 49.96mm, where all the others were pretty spot on 49.97mm. The lower spec for grade no.1 is 49.961mm. I'm getting access to some better gear my next days off to double check everything, but in the case that the big end is right on that bottom spec, is it pretty much just a case of straight to the machine shop for machining and oversized bearings? I understand I need to measure the tunnel as well to work out my oil clearance, but it's the different grade bearings in the manual that are confusing me. What is generally the process when one journal would still technically be in spec, but in a different grade?  Thanks for coming to my Ted talk
    • You need to visit Ipswich. Plenty of clapped out R32 and R33s running around here as daily drivers. And when I say clapped out, they're how you'd look at a VN, when it's the year 2010...
×
×
  • Create New...