Jump to content
SAU Community

Recommended Posts

Pat, if you know you're headed for CGT, invest in some risky shares. If you realise any losses, you can roll them over year to year and eventually subtract them from dem house selling gains = 30% less risk investing in said shares.

Your move Tony/Ric

But I'd rather keep my dollar than get 30cents for every dollar

this. so much.

Speaking of dodgy, bloody office/laboratory people. someone's birthday in a department means afternoon cakes and at least an hour of bludging and sitting around.

start by owning a house, not $80k worth of toys :P

haha true, I've got some shares I could use for a deposit but cbf at this stage they're going well :D

but yeah gotta do the whole 'grown up' thing soon :\ #YOLO

Edited by UNR33L

Sadly no. Property was never my primary residence so ill get shafted when/if it comes to sell.

Pat, if you know you're headed for CGT, invest in some risky shares. If you realise any losses, you can roll them over year to year and eventually subtract them from dem house selling gains = 30% less risk investing in said shares.

Your move Tony/Ric

My move would be flux capacitor go back in time

And tell Pat if you move into your house for 6 to 12 months it could save you ten of thousands of dollars in tax down the track when you sell

Should of had an accountant friend back then :P

My move would be flux capacitor go back in time

And tell Pat if you move into your house for 6 to 12 months it could save you ten of thousands of dollars in tax down the track when you sell

Should of had an accountant friend back then :P

Haha I was aware but did not pursue.

Rental income helped get larger loan 95LVR and plan was to move in however Perth has shot that plan down.

However I do like Birds' strategy. Was unaware of that haha

Haha I was aware but did not pursue.

Rental income helped get larger loan 95LVR and plan was to move in however Perth has shot that plan down.

However I do like Birds' strategy. Was unaware of that haha

Sure if you have time to share trade whilst your over there :P

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Got the motor out and torn down. I'll be dropping off the block Monday. Luckily the scoring on Cyl6 is much less pronounced then the pictures made it out to seem. It can barely be felt. If you pass your finger over it 10x you'll barely notice it. Hopefully by some chance it will only require a honing. I'm not in the mood to buy one size larger pistons or another block. Oddly enough my 6th cylinder with the scoring has extremely clean intake valves compared to my other 5 cylinders. I'm worried the scoring was caused by too much fuel or Water/Methanol washing the cylinder. I'll review some old logs to confirm.  This was also the first time I pull an engine with the transmission still attached. It went much better then expected. I was worried my CD009 wouldn't make it easy due to its sheer size but it was much easier this way. 
    • From the pictures I have when doing the job the flywheel is the same diameter, I don't think they're playing weird tricks like putting weights at the outer diameter to increase flywheel inertia or anything like that. The OEM flywheel is definitely heavier, but it's not a huge difference. Quoted weight savings of the clutch is 2 kg so I can't imagine the flywheel being lighter than ~7 kg. Kind of regret not weighing it before the clutch went into the car but as far as driveability goes I have no complaints.
    • HKS trigger kit should be very easy to integrate with a Link. It's a 36-2 crank trigger. Hard part is finding the motivation to take off the timing belt and everything on the front of the engine to install it. You also need to cut out a hole in the oil pump housing so the sensor can read the trigger wheel. Changing out the cam sensor for a 24 tooth setup is probably good enough but as others have mentioned depending on what underlying assumptions are changed it becomes more of a problem. Reading the crank state off of the cam is an abstraction that works in the general case, but if you have an edge case it makes less and less sense. There is a GTX2860 gen 2 that can take a compact 5 bolt housing so it's direct bolt on but I'm not 100% sure of what's involved. Peak compressor efficiency drops off a bit on these turbos vs -5s, 77% vs 73% but you get way, way wider region of operation. The -5s have a really strange surge line in their compressor map that is all over the place. If you think the hot side on the -5s aren't open enough you can try the Tomei T550B turbos which a local tuner seems to be happy with:
    • i need a complete tail light for my R33 GTR if you have please let me know.
    • I need a great maintenance workshop around Idaho, if you know one please let me know..
×
×
  • Create New...