Jump to content
SAU Community

Recommended Posts

The engine light started flashing at me when I turned the key too on in my 32 gtst, wasn't like that last time I drove it. It stalls when I touch the accerator and struggles to start, I havnt driven since, only moved it from where it was parked, And holy shit it has no power to even move it, I did some research on how to check the ECU fault codes but didn't have any luck when doing so (i might possibly be retarded) im keen to get this sorted ASAP

Any help would be awesome as I'm ripping my hair out trying to figure this shit out myself >_<

I'll answer any questions as best I can...

Mods are:

Exhaust

Gtr FMI

Coil packs

Pod filter

r33 series 2 turbo and dump pipe

Running 10psi

Stock ECU, AFM etc

Its in limp home mode. Disconnect the afm and see if it runs better.

U need to try again to get the fault codes. They should tell u which sensor is farked

Where are u located?

Replaced the AFM, disconnected the battery for 10min, reconnected and still playing up, if I touch the throttle and gradually bring the revs up it doesn't misfire (much), but if I stomp the throttle it cuts out for a second then spits like a mofo, and shoots fuel out the exhaust.

I'm located on the gold coast..

dude i got the same problem with my stagea. ive been looking around on the net and i from what ive found so far, it could be AFM or the o2 sensor. im planning on replacing my o2 sensor tomorrow if i can find a shop that has one. im also on the gold coast so if i fix my problem, id be happy to help you with yours

Awesome :D, well ive ruled out the AFM itself (replaced with a new one) could still be the looming? And I replaced the o2 sensor about 6weeks ago with a second hand one from nizzpro, whether or not the o2 is gone again I'm not sure, Nizzpro stock brand new o2 sensors for $80 or second hand for $40. Let us know how you go, i just don't want to dump It into a mechanics hands just yet if its a small problem for them to charge me labour for unscrewing a couple things :/, could be a coil or igniter? Possibly an air leak? Under boost sucking air that doesn't go through the AFM? Or leaking air pressure? Really starting to niggle me haha

Another thing I noticed, after resetting the ECU, and simply turning the key to on (not starting the car) the engine light spazes out straight away so leaning more so towards an electrical issue..

  • 5 months later...

hey mate i have an issue similar to this,

i have same car, car runs fine in neutral and revs to about 5K than mild backfire, it was in a dudes yard for ages but ran fine got it nearly home and it started loosing power really bad!

now it does not have any power when in gear to move a meter forward or a meter back. it just looses revs and stalls when clutch is released, umm its pretty stock just a pod filter,

i ran 10 liters of high octane with injector cleaning fluid and it has not helped i thought it was possibly clogged injectors this did not work, i need help aye im pretty shit with cars

any help would be great!!

Cheers man.:cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of an update to this one. Having some issues on the dyno that held us back (boost spiking) and I want to pass some info over you guys and see what you think is wrong with my setup. The current readout on this dyno is 462rwkw on a low reading dyno so keep in mind it is a real world 500rwkw setup on a hub dyno. Don't read into the power figure too much as a sign of the issue. The short and curly of it is: 2.8 Litre Racepace build RB25 NEO N/A Head with VCT (internally standard however ) Borgwarner EFR 8474  Turbosmart 50mm Straight Gate + Mac valve 6Boost Manifold 4" dump to full 4" exhaust (nil restrictions) Wastegate plumbed back in and all angles in the exhaust system are acceptable and not too sharp. GFB SV52 BOV in cooler piping  Turbosmart BOV in EFR Housing   The issue we are having is it comes onto full boost for example at 4000rpm and spikes to 24/25psi, before dropping down to 17psi before slowly rising back up to the target boost of 23psi. It was extremely uncontrollable and the tuner actually had to ramp in boost progrssively with each 1000rpm on each boost setting we selected to try and reduce the amount of spiking. Sometimes we would see a drop of 10psi from the peak at the beginning of the run, to the low, until it took the next 500-1000rpm to stabilise back up to the target boost. The tuner is pretty confident that the straight gate is just a poorly designed product and leaks too much boost upon cracking the gate open and theres no way to fix it other than going to a poppet valve. He's also confient theres no ignition breakdown or floating valves. The fueling is extremely stable as well. Turbo speed is somewhere around the 109,000rpm area. The spanner in the works for me is that prior to this Borgwarner and StraightGate, the car was tuned on -5 twins at a diferent tuner, and he also had issues controlling the boost with it spiking around the same rpm range, so to me this sounds like the same issue and it can't be anything on the turbo side as this was all changed and I think the behaviour is extremely similar, if not the same. We also removed the mac valve and did a run on wastegate pressure and it still spiked and had the same behaviour. My thoughts on possibilities are: Boost Leak VCT Cam Gear isn't reliably activating consistently - (On this however, we did a run with the VCT disabled and the boost still spiked) Turbosmart BOV is not handling the boost? However this seems unlikely to not be able to handle 20psi. I have a couple of logs that I can't make sense of if anybody knows how to read them and can obtain further logs of other parameters if they are not enough, happy to pay for anyones time. The dyno readout with the power figure is the most recent last week. The other picture is from two weeks prior to that where we couldn't break 400kw (we removed the cat), however the issue of the boost control persisted. @Lithium @Piggaz @burn4005 @GTSBoy @discopotato03 I've tagged those that were quite active in recent pages here, no disrespect to those that know turbos well but I missed tagging. Cheers 
    • I recently purchased a 2018 Infiniti Q60, which has an SD card navigation map. I can see my system has options for real time traffic updates etc, and am wondering if there is something I can purchase to get this working? I can see there are at least updated maps for USA and Canada, but nothing for Australia. Surely Infiniti took changing road systems and city expansions into account when they decided to use an inbuilt navigation over Android Auto/Apple Car Play, or are we doomed to drive on streets that don't exist in the navigation system if you drive to a new area?
    • Luckily I didn't put in etch primer as I just found out it's not compatible with my body filler lol. Also just need to sand the panel anywhere between 150-400 grit so I'm in the clear there. It does say to not apply to soft old paint, I assume that means paint that is flaking, peeling,etc
    • @dbm7 and @GTSBoy thank you both very much! will give that a shot!
×
×
  • Create New...