Jump to content
SAU Community

Recommended Posts

my stageas engine light comes on and the car hesitates and runs rough between 1000-2000rpm. today it got really bad and the revs started dropping and then picking up again a lot before finally stalling. i did a diagnostic check on it by bridging the 2 connections on the diagnostic port and i got code 55 - all cear. WTF.

ive cleaned the AFM, swapped the coils, replaced the sparks, cleaned the AAC valve and filled up with 98 premium

the previous owner put an aftermarket exhaust on it and has cut the connection to the o2 sensor after the cat (there isnt a sensor to plug it into). the rest of the car is bog stock. not even a pod filter

Link to comment
https://www.sau.com.au/forums/topic/380215-engine-light-on/
Share on other sites

thanks dudes. i found the posts on how to fix it. nicely soldered up now :)

Is it fixed now??? I have a spare unit that needs soldering so want to know if it worked for you???

Link to comment
https://www.sau.com.au/forums/topic/380215-engine-light-on/#findComment-6070970
Share on other sites

not getting any more AFM fault codes but the car is far from fixed. still doing the weird stalling thing between 1-2rpm but i went to japanese parts n performance in molendinar and got another AFM just to make sure. same shit happening between 1-2rpm

so to answer your question; i THINK it fixed the AFM..... :S

Link to comment
https://www.sau.com.au/forums/topic/380215-engine-light-on/#findComment-6073662
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Latest round of updates on the car. I purchased and installed a SWS clutch slipper to help with 60ft times and got some second-hand good condition 275/40R17 Hoosier DR2 radials. Test and tune in November showed the tyres were an upgrade over my over 15 year old mickey Thompson's and I got a 1.8 second 60ft and pb et of 11.71 but even then, that run wasn't great due to rain and driver error (the event got called off 10 minutes later fast forward to the weekend just gone 25th of Jan and there was finally a break in the weather to let racing happen. The first run the track was slippery and only managed a 12.1@129 Second run the track was better and got a new pb et and mph: 11.54@131   Lith and I then worked out that I installed the previously mentioned clutch slipper incorrectly and its never been working, and I had just been dumping the clutch the entire time, we also noticed it was on street boost and not race boost. So I lined up for a third run with the car turned up in the first two gears, but the passengers side axle objected to clutch dumps and left the chat which stopped my weekend.   so there will be another attempt in the future once I replace the tyres as they rubbed and are stuffed now. but a low 11 should be on the cards.
    • Ceramic coating and heat shielding, you mean?
    • Turbos don't require pulling the motor apart so that's "easier". I would recommend the Nismo R3 turbos instead if you want to do stock twin turbo. It doesn't make as much power as the 2530s but it's only like ~50 whp off the mark and should have better response (ball bearing CHRA, slightly smaller turbo). A local that went with a Garrett G30 and 6boost manifold recently nearly burned his car to the ground after the hood insulator started melting and and burning so if you go single turbo I recommend doing a lot of research and validation work to make sure you don't do the same.
    • New rear lights, filler panel sprayed, cleaned and back together    before, during, after shots 😍
    • 100% is gyprock, I agree. Slip of the keyboard. Haha! I left my indicator bulbs out to save a bit of weight.
×
×
  • Create New...