Jump to content
SAU Community

Recommended Posts

1994 R32 GTR, the car's had blitz blow off's going to atmo for a while, gone to reinstall the stock blow off, removed the blanking cap from the pipe to have a fair amount of oil come out, what's this mean? a blown turbo oil seal prehaps? pic of the pipe i'm talking about below.

view through the front bumper

BOV.jpg

with the bumper removed

BOV4pipe.jpg

the blitz blow off valves.

BOV3.jpg

You found oil in the dead end of the recirc line? That's the lowest point, I suppose it could find its way there whilst it was blocked off at the BOV end if it was still connected at the turbo inlet end, but it could be residual from when the recirc BOVs were still being used. What's a "fair amount" of oil? 1 tablespoon? A cupful?

There's always some oil in the intercooler plumbing - the cam cover breathers also connect into the turbo inlet and depending on how much your engine breathes, you'll have anything from a little to a lot of oil in there somewhere. A lot of oil is of course undesirable - for one it tends to suggest a lot of breathing which is a sign of wear, and it also tends to promote detonation because engine oil being breathed in with the air-fuel mix has a low detonation threshold.

Oil can of course enter the induction tract from leaky turbo seals. It can be hard to work out where it's coming from though.

If you've got enough oil being breathed in to cause you running problems, then you'd probably notice a reasonable amount of oil usage across a service interval.

called previous owner, he say's he's been running the blitz BOV for around a year which would explain the build up of oil, no air flow through the pipe meaning no way to get rid of it, also explains the oil leak onto the front bumper, reinstalled the stock blow off valves and plumbed them back in, solved my over fueling issue and leaking oil issue, oil's green because the previous owner used martini oil's, which are green.

Edited by ttoks

If you want to do the right thing by your car, you need to pull off the intercooler, return pipe and all the intake hoses and give them a good clean.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Most important of all, invest in a catch can that actually works or you will be cleaning it all again in a few months.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Best cleaning methond is a 50/50% mix of Methylated Spirits & Kerosene.

:thumbsup:

Please tell me you had the motor and car properly inspected before purchase?

Just cleaning the pipes would be the end point. For safety sake get a comp/leak down test done.

Especially given the price it was selling at - perhaps you've just found the reason why it was cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...