Jump to content
SAU Community

Recommended Posts

1994 R32 GTR, the car's had blitz blow off's going to atmo for a while, gone to reinstall the stock blow off, removed the blanking cap from the pipe to have a fair amount of oil come out, what's this mean? a blown turbo oil seal prehaps? pic of the pipe i'm talking about below.

view through the front bumper

BOV.jpg

with the bumper removed

BOV4pipe.jpg

the blitz blow off valves.

BOV3.jpg

You found oil in the dead end of the recirc line? That's the lowest point, I suppose it could find its way there whilst it was blocked off at the BOV end if it was still connected at the turbo inlet end, but it could be residual from when the recirc BOVs were still being used. What's a "fair amount" of oil? 1 tablespoon? A cupful?

There's always some oil in the intercooler plumbing - the cam cover breathers also connect into the turbo inlet and depending on how much your engine breathes, you'll have anything from a little to a lot of oil in there somewhere. A lot of oil is of course undesirable - for one it tends to suggest a lot of breathing which is a sign of wear, and it also tends to promote detonation because engine oil being breathed in with the air-fuel mix has a low detonation threshold.

Oil can of course enter the induction tract from leaky turbo seals. It can be hard to work out where it's coming from though.

If you've got enough oil being breathed in to cause you running problems, then you'd probably notice a reasonable amount of oil usage across a service interval.

called previous owner, he say's he's been running the blitz BOV for around a year which would explain the build up of oil, no air flow through the pipe meaning no way to get rid of it, also explains the oil leak onto the front bumper, reinstalled the stock blow off valves and plumbed them back in, solved my over fueling issue and leaking oil issue, oil's green because the previous owner used martini oil's, which are green.

Edited by ttoks

If you want to do the right thing by your car, you need to pull off the intercooler, return pipe and all the intake hoses and give them a good clean.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Most important of all, invest in a catch can that actually works or you will be cleaning it all again in a few months.

Flush the intercooler with petrol until you can shake about 200ml of petrol in there and have it poor out clean. Same with the return pipe.

Best cleaning methond is a 50/50% mix of Methylated Spirits & Kerosene.

:thumbsup:

Please tell me you had the motor and car properly inspected before purchase?

Just cleaning the pipes would be the end point. For safety sake get a comp/leak down test done.

Especially given the price it was selling at - perhaps you've just found the reason why it was cheap.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I think my main complaint with your idea is that there is a veneer of idealism spread across it. You want the simple numbers to make it easier, but all they will do is make it easier for someone to come to the wrong conclusion because the fine details will kick them in the nuts. As it is right now, the tiny bit of arithmetic is NOT the obstacle to understanding what will fit and what will not fit. The reality of trying it is what determines whether it will fit. If you had a "standard rule" that R34 GTT guards have that magic 100mm space from the hub face to whichever side you were worried about, and someone said "excellent, this wheel is only 98mm in that direction, I'll just go spend $4k on them and jam them on my sick ride".....they would just as likely find out that the "standard rule" is not true because the rear subframe is offset to one side by a fairly typical (but variable) 8mm on their car and they only have 92mm on one side and 108 on the other.
    • It still combines inches with mm, especially when you have .5 inches involved, and mm and inches that can go in either direction. This would give a clear idea on both sides of the rim, right away, with no arithmetic. Even better if somebody gives you the dimensions of the arch of multiple cars. i.e GTR may be 125mm, a A80 Supra may be 117mm, or something along those lines. Yes, you can 'know' that going from a 10in rim to a 10.5in rim with the same offset moves both sides about 6mm, but you still have to 'know' that and do the math. Often it's combined. People are going from 9.5 +27 to 10.5 +15. You may do the math to know it, but if it was going from (I had to go look it up to be sure) 241mm/2 - 27 - 93.5mm from the center line to (more math) 266/2 - 15 (118mm) from the center line. Versus 93mm vs 118mm. It's right there. If you know you have a GTT with 100mm guards you can see right away that one is close to flush and the other absolutely won't work. And when someone says "Oh the GTR is 120mm" suddenly you see that the 10.5 +15 is about perfect. (or you go and buy rims with approximately 118mm outward guard space) I think it's safe to say that given one of the most common questions in all modified cars is "How do offsets work" and "How do I know if wheels will fit on my car" that this would be much simpler... Of course, nothing will really change and nobody is going to remanufacture wheels and ditch inches and offset based on this conversation :p We'll all go "18x9+30 will line up pretty close to the guards for a R34 GTT (84mm)" but 'pretty close' is still not really defined (it is now!) and if you really care you still have go measure. Yes it depends on camber and height and dynamic movement, but so do all wheels no matter what you measure it for.
    • But offsets are simple numbers. 8" wheel? Call it 200mm, near enough. +35 offset? OK, so that means the hub face is that far out from the wheel centreline. Which is 2s of mental arithmetic to get to 65mm to outer edge and 135mm to inner. It's hardly any more effort for any other wheel width or offset. As I said, I just close my eyes and can see a picture of the wheel when given the width and offset. That wouldn't help me trust that a marginal fitment would actually go in and clear everything, any more than the supposedly simple numbers you're talking about. I dunno. Maybe I just automatically do numbers.
    • Sure! But you at least have simple numbers instead of 8.5 inches +/mm, relative to your current rims you do maths with as well, and/or compare with OEM diameter, which you also need to know/research/confirm..
×
×
  • Create New...