Jump to content
SAU Community

R33 Intake, What Fuel Rail (R32/33/34) Gives The Most Injector Options?


Recommended Posts

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

so do you guys have experience using that deatschwerks injectors? prices look good

just got my motor going again with some 1000cc side feed deatschwerks. had a little trouble with the latency but all sorted now and idle just as well as the nismo 555s they replaced. can drive around at low revs and idle like a stocker with enough fuel capacity for 800+hp

The 740s are only $50 more than the 550s, there is no reason to not get them is there? Only aiming for 250kw, maybe 300 in the future but I see 250 being plenty for quite some time.

Edited by Rolls

Hi Rolls i just did the injectors on my 34 gtt with stock rail and there are so many options.

Bosch ev14 injectors come in many sizes.

Sard

Nismo

Deatchwerks

Seimens

List goes on

All the ones i listed are bolt in. You dont need spacers or adaptor.

The only change needed is the plugs are different.

The bosch EV14 injectors come in sizes up to ID 1000 cc

You need to buy the 3/4 injectors for a neo. I just put them in my 34 with stock rail stock intake.

I paid 550ish for injectors 180ish to install and under half a hour to tune.

Plus RB20's use side feed injectors neo's use top feed

Edited by whitneybra

Rolls im in the same boat as you, im also looking for injectors that are regency friendly with the stock fuel rail, either going to go nismo or deatchwerks, im pretty sure the deatchwerks are just a highflowed stock injector? if anyone can confirm...so should be same colour etc.

Hi Rolls i just did the injectors on my 34 gtt with stock rail and there are so many options.

Bosch ev14 injectors come in many sizes.

Sard

Nismo

Deatchwerks

Seimens

List goes on

Nismo only come in 480cc which is too small imo, especially if you ever want to run E85.

The destschwerks are the only option that are truly direct fit. The rest require some form of modification to work.

Yeah going to buy the 740s, not cheap but I want to pass and want room to move in the future if I want to try E85 or aim for 280kw

Thanks for the help everyone!

Edited by Rolls

Yeah going to buy the 740s, not cheap but I want to pass and want room to move in the future if I want to try E85 or aim for 280kw

Thanks for the help everyone!

where are you purchasing them from mate?

Thanks everyone for correcting me about the rb20 injectors

www.tuffcarparts.com shoot these guys a email they sell lots and there was even a group buy here on SAU

Edited by whitneybra

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @GTSBoy Yeah i know. The RB20 has 180Nm torque and the gearbox "should" take up to 400Nm if you are not doing stuff like drag/drift or dumping clutch and of course then it is pure "luck" on how will it last. My problem is (i think i said this in different post) that my car was very badly maintain so i would not be suprised if the oil in the gearbox was not changed until i bought it. Yeah the gearbox seem little bit sad.   @Sxnjeet the +T seem very interesting but from where iam from it was nearly "impossible" to done right and not blow twice as money as just swap for the RB25.
    • Hi, I went to the MINES shop here and bought something.. Niikura-San just happened to be there so I managed to take some pics and got him to sign my dash surround thingy. Its still wrapped in plastic back home.. I was thinking how to preserve the signature??? Im sure someones thought of this and done this in the past.
    • Perfect - thanks Joshuaho96!  Will see what I can source.
    • If the plastic wore, the paint will wear quicker. Heck, most car manufacturers cant keep the coatings they put on their buttons/trims alive these days for more than 5 years... A cheap paint won't do it!   However, you can get away with high quality vynil wrap, primarily in areas that won't cop much abuse. Skip colour matching, and just try and wrap a specific area with an edge in a new colour.   PS vynil wrapping is a prick of a job, and I suck at it, even for a small dead flat surface...
    • I think this is more a question you should ask the tuner. My assumption is you have nothing plugged into the original pin for ring gear crankshaft, which is where your map sensor should get wired to, but now you've asked the tuner to disable it. I'm assuming (because I haven't memorised your setup) you are using RB25 ECU on the RB20 loom, to plug into an RB25. You will want to check what else is connected potentially backwards between the engine, loom, and ECU. You might be all fine and safe. The best solution you could have done is wire in a map sensor, and leave the ECU able to read a map sensor.
×
×
  • Create New...