Jump to content
SAU Community

Help. Alarm Going Off For No Reason And Cant Turn Off With Key...

tammy

By tammy,
in General Maintenance

 Share

Recommended Posts

tammy Contributor

tammy

Posted
Posted

So I came outside today and my alarm was going off really quietly for no reason at all. I was pushing the alarm button on my key and it wouldnt turn off. My mate helped me over the phone to turn the alarm down so I cant hear it....

Iv changed the battery in the key but still no go. What do I do now??? This has never happened before.

Im also unable to start my car.

thanssss....

central coast person Proficient

central coast person

Posted
Posted

Dont jump start it because where ever you go you better hope they have a new battery for you.

Get a new battery. Alarm's do that when your have no battery or disconect the battery from the car.

Hanaldo Grand Master

Hanaldo

Posted
Posted

Dont jump start it because where ever you go you better hope they have a new battery for you.

Get a new battery. Alarm's do that when your have no battery or disconect the battery from the car.

Or just drive it long enough to charge the battery?

If the car hasn't been driven for awhile then the battery would have been drained by the immobilizer, just jump start it and take it for a good drive. If the battery just went flat overnight, you've either left something on in the car or the battery has conked it. If you're not sure how to do a load test on a battery, best to take it to your local battery shop so they can test and replace if necessary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32gtr sputtering and stalling

      By MBS206 · Posted

      I agree, don't go trusting those trims. As I said, first step is to put the logger away, and do the basics in diagnosis.   I spend plenty of time with data loggers. I also spend plenty of time teaching "technicians" why they need to stop using their data loggers, and learn real diagnostics.   The amount of data logs I play with would probably blow most people away. I don't just use it to diagnose. I log raw CAN data too, as a nice chunk of my job is reverse engineering what automotive manufacturers are doing.
    • joshuaho96
      R32gtr sputtering and stalling

      By joshuaho96 · Posted

      I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
    • MBS206
      Neil's R33 Gts-t Build

      By MBS206 · Posted

      Silly question, as I bet you've checked already, but the motor turns over by hand yes? I suspect Neil has a spare starter, though if not, I believe I have a spare R33 (or two) starter.
    • Duncan
      NPboosted manifold fitting purpose

      By Duncan · Posted

      Yeah just run one of those posts to the Link like GTSBoy said. From google it looks like a "mishimoto boost controller" is a manual boost controller. Since you already have the link just buy any MAC valve and plumb it in where the mishimoto is now. Wires to the solenoid should come from the Link's / standard loom boost control wiring (I guess you have an r32, not sure if it is gtst or gtr, if it is GTR where is a 2 pin connector near the engine bay fuse box/injector resistor for that purpose, assuming the standard boost controller is gone)  
    • GTSBoy
      NPboosted manifold fitting purpose

      By GTSBoy · Posted

      No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol. The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case. Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.
×
×
  • Create New...