Jump to content
SAU Community

Soarer, No Power To Anything, Lights, Dash, Everything.


Recommended Posts

So, the story goes like this.

I had to replace my fan shroud to clear a roadworthy inspection, and due to that, I had to take out my battery and the battery tray so that the shroud would actually fit.

When i put everything back together, including the battery, the car wouldn't start and there's no power to anything. And there's this 3rd wire that's confusing the hell out of me.

I was thinking, how hard is it to put back a battery right? Its apparently pretty damn hard. Attached is a picture of the 3 wires. I've checked the fuses, they all seem fine. Might be a dead relay? Or no earth?

post-61332-0-77355200-1318947653_thumb.jpg

help me solve this issue.

ok so that's not the best pic I've seen, but it kinda looks like the positive is hooked up to something touching the chassis,

ie the earth/negative side.

so they need to be reversed.

or I just could be looking at that completely wrong..or drunk!

Is the battery charged? Use a test light to trace the power to where it stops or if there is any power in the battery.

The charge indicator looks red in the pic.

Need a better picture of the 3rd wire u speak of. What sort of end does it have

the battery light has been red for as long as i can know, car still drives fine, in fact, two nights ago, i had gone for some spirited driving.

I just know its something bloody silly. And i also realised i should have taken the clamping things off instead of the wires, so, lesson to some, don't do mech work when you're sleepy as hell. Charge across battery is 13v. I've connected a jumper pack to the leads and no power either.

post-61332-0-24542900-1318979855_thumb.jpg

post-61332-0-65152500-1318979884_thumb.jpg

lol andrew, its been sorted, thanks man. Its a massive facepalm moment. I had actually thought yesterday arvo, that i should have connected both + sides to each other but, i didn't dare to do so. fuses and relays are scary things when blown. but nothing's wrong now.

Cheers guys!

lesson learnt, take off the clamping things instead of the leads.

Haha glad you got it sorted. Just looked at the pic and thought it looks fairly standard, one line on the positive will go to the starter motor and the other line will go to the fuse box, not sure where the problem is :P

Haha glad you got it sorted. Just looked at the pic and thought it looks fairly standard, one line on the positive will go to the starter motor and the other line will go to the fuse box, not sure where the problem is :P

yeah i know right, electronics just do my head in. when i see those wires go into the darkness. meh.. my mind shuts down.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • Plus, you'll get great experience in bedding in pads!
    • I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • You miss spelled bearings...
×
×
  • Create New...