Jump to content
SAU Community

Recommended Posts

1991 R32 GTR

Car is making 270rwkw on 18 psi on a very safe tune.

GT-C Volk 18x9's all round.

Motor rebuilt approx 8000km ago

Freshly serviced and ready for a new owner.

Reco block + head were used.

chemical clean all parts, full machine, clearance and blueprint.

ACL comp bearings

JE Forged piston kit

H-beam rods

MLSR steel head gasket

oil restrictors

Genuine nissan gasket set

all new hoses

new genuine thermostat

new water pump

new timing belt

nismo radiator cap

new battery

new heater core

re gassed air con

nismo diff bushes

cradle spacers (pineapples)

600cc injectors

nismo plugs

Garret 28/60 turbos -7

Apexi power fc with hand controller

full kakimoto 3' exhaust

blitz 4 stage boost controler

R33 GTR crank

N1 oil pump

momo stearing wheel+ gear knob.

Tomei 310km dash cluster

new slotted rotors all round (dba)

koyo rad radiator

baffled sump

bosch fuel pump

central locking + alarm and immobilizer

Good stereo, good tires

Car interior has been retrimmed in leather

car is extremely well looked after washed every week.

always garaged as long as i owned it in TAS

im looking for 24,000 ono

which i think is fair for such an amazing car.

i am also open to swap + cash or straight swap for something of interest.

post-88564-0-36149900-1319090688_thumb.jpg

post-88564-0-07970200-1319090731_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/380720-fs-freshly-rebuilt-r32-gtr/
Share on other sites

http://www.skylinesaustralia.com/forums/topic/370504-1991-r32-gtr-sniper-mint-condition/page__p__5905955__hl__mint__fromsearch__1#entry5905955

Looks like its one of the better ones out there.

Interesting that your advertising it for I assume more than you bough it for.

Good luck with the sale.

I'm selling it due to just moving to Melbourne work is 45 minutes away so I'm looking for something more standard feels like i would be wasting it putting big Kms on such a nice and powerful car when someone can put it to better use.

hmmmmmmm... i went n saw this car just before you bought it. and i know a fair bit about the car... having said that, this car has history being shane's first 32r and is still impressive..

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You're not wrong, but more than a few times I've heard of people running into issues where their injector characterization isn't quite right and that approach works for that specific configuration but once they switch over to a new set they discover a whole bunch of stuff wasn't set up correctly. It's slightly more annoying to reverse engineer the OEM MAF transfer function but you already have the sensor wired up to the factory harness so keeping it around for a few weeks more while you figure out the tune is easy enough. I've seen GM also use a combination of both MAF + MAP in their ECUs before, MAF is for steady state and a calculation of the cylinder VE to correct the base VE table, then in transients it uses that calculated VE + raw MAP to determine cylinder filling somehow.
    • I know this one’s the BB one. My tuner did make mention about the actuator. I am curious about the VCT as well
    • Might also needs a stronger actuator with the right preloading. With older 2019 built bush G3 units, BB upgrade or 21U housing down size makes a pretty decent gain in response as well. 
    • Hey lads  so im finally putting together my rb30 forged bottom end and ran into an issue. I measured my main bearing clearance with arp main studs torqued to 60 ft-lbs using ACL H series STD size bearings and standard, un-ground crank shaft journals and got an oil clearance reading of about 1.3 thou measuring straight up and down and about 2.8 thou measuring at a 45 degree angle (just above and below the parting line). My machine shop said they measured the main tunnel and it was all within spec (they didnt say the actual measurement) and to go with a standard size bearing, which i have done and the clearance is too tight, I'm guessing because of the extra clamping force from the arp studs distorting the main tunnel. I was wanting to run about 2.5 thou main bearing clearance.  My questions are: 1. could i just use the HX extra 1 thou clearance ACL bearings? that would fix my straight up and down clearance making it about 2.3 thou, but then would the side to side clearance be too big at around 3.8 thou? 2. what actually is the recommended main bearing clearance for measuring near the parting line / side to side. i know its supposed to be bigger as the bearing has some eccentricity built into it but how much more clearance should there be compared to the straight up and down measurement? at the moment there is about 1.5thou difference, is that acceptable or should it be less? 3. If i took the engine block + girdle back to the machine shop and got them to line bore the main tunnel (like i told them to do the first time, but they said it didnt need it) what bearing size would i buy? the STD size bearing shells already slide in fairly easily with no real resistance, some even falling out if i tip the girdle up-side-down. If im taking material out of the main tunnel would i need a bearing with extra material on the back side to make up for it? this is probably confusing af to read so if something doesn't make sense let me know and ill try explaining in a different way. My machine shop doesn't come back from christmas break until mid January, hence why i'm asking these questions here. TIA for any help or info 
    • I bought the model back in Japan in Feb. I realised I could never build it, looked around for people who could build it, turns out there's some very skilled people out there that will make copies of 1:1 cars or near enough. I'm not really a photo guy... but people were dragging me in a group chat for the choice of bumper as someone else saw the car before it was finished as they are also a customer of that shop. I took the photo in the above post because I was pretty confident that the lip would work wonders for it. Here's some more in-progress and almost-done pics. It gives a good enough idea as to what the rear looks like!   I have also booked in a track day at the end of January. Lets all hope that is nothing but pure fun and games. If it's not pure fun and games, well, I've already got half an engine spare in the cupboard 
×
×
  • Create New...