Jump to content
SAU Community

Need help with getting the studs off urgently :(

inark
 Share

Recommended Posts

inark Grand Master

inark

Posted
Posted

Hi Guys,

Im trying to replace all 5 wheel studs on the rear of my R32 GTST.

Ive taken the calipers off as well as the actual rotor itself but i dont know if i need to undo anything more to get the plate that the studs go thru off or just keep trying to pry the damn thing off...

any help would be great as im supposed to be getting these on by this afternoon cause someone wants to test drive the car :)

SteveL Mentor

SteveL

Posted
Posted

The studs are a press fit in the rear hub. The hub is a spline fit to the driveshafts and held in place by a big arse nut done up to a HUGE torque (there's also a lock plate and split pin over the nut). I think the nut itself requires a 30mm socket, plus you'll probably need a puller to get the hub off - after you've got the nut undone.

It might be possible to drive out the old studs with the hub in place after you take off the handbrake shoes to give enough clearance (you should see those 'behind' the hub after the disc is off). If you can get the old ones out that way, getting the new ones in should be fairly easy. If your not sure tho, don't try esp with time so short.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Powder coating wheels

      By MBS206 · Posted

      I'm interested if anyone agrees with what you've said, and can give a good reason. Temperature of powder coating should be below any temperature you'd use to alter the wheel structure.  Powder coat typically 200 to 250. Annealing if that's what people are claiming would be occuring, starts at 300, and depending on the alloy, can need even up at 400+.   That's the only part I can think of that could cause an issue that people are believing it's from the rim losing hardness and becoming too soft.
    • MBS206
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By MBS206 · Posted

      Negative probe should be on the cars chassis. Positive on the wire.   Start as said above by unplugging everything (unplug the lights, and switches. Now at the switch, there is a wire from the fuse, to the switch, so out your positive on that terminal. It should read open circuit. If it reads something, especially a stupid low value, the short is somewhere between the fuse and the switch. If that's fine, now put the positive probe on the wire that goes to the headlight (at the switch plug). If it reads stupid low, the fault is from the switch, to the headlight.   Another quick test, is take the whole LED light setup from the left, and plug it into the right side, does it still blow the fuse? If you put the right hand side led light setup on the left hand side wiring, does the left hand side wiring now blow?  If the blowing fuse swaps from right to left doing this, your LED lights are the issue.
    • dyl33
      Powder coating wheels

      By dyl33 · Posted

      Anyone know if it's a problem to powder coat forged alloy wheel centers (Rays/Volk GT-C). some say it's bad and can damage the alloy, some say it's not a problem.
    • kevboost7
      One Headlight isn't working - Driver Side Fuse Keeps blowing

      By kevboost7 · Posted

      Hey guys, I'm reviving an old post but I'm finally getting around to working on this now. I removed the battery to get a better look at the wires and i traced the wires from the headlight to the fuse box in the engine bay, but the wiring looks fine? The wiring for the R/H headlight is 3 wires and then is bundled up with the large diameter wire that goes underneath the fuse box. I didn't take it apart yet. I know you said that its a short circuit somewhere between the fuse box and the headlight. But could it be the headlight switch on the dash? Also, i pulled out my multi-meter and set it on the Ohms, but i'm not sure where to put the negative probe and the positive probe.     
    • wrxhoon
      WTB R33 GTST Catch Can 2L or Bigger

      By wrxhoon · Posted

      I have a 2 lt in Sydney. It was fitted on a R33 GTR, not used for several years . If you are interested email me on: [email protected] I'm not on this forum much .
×
×
  • Create New...