Jump to content
SAU Community

Recommended Posts

i don't drive my Stagea (S2 C34 RS Four S) all that much, as it's the wife's daily

however, drove it a while today and it's not making any boost. like zero, none

feels sooooo slugish

recently serviced by a reputable workshop (3 weeks ago)

battery went flat the other day, but i wouldn't imagine that would cause a problem?

any ideas on what i can check/do?

Edited by Stooge007
Link to comment
https://www.sau.com.au/forums/topic/380980-dude-wheres-my-boost/
Share on other sites

Even reputable workshops can make mistakes! Check all the pipes and joiners for leaks or clamps not done up properly. Is the boost gauge connected properly? If you're careful you can pull the hose off the actuator to see if the problem is with the boost control and if it is work backwards to see where it is going wrong.

look down the passenger side of the engine and see if the wastegate is hooked up the rear housing

did she hear it make any "funny" noises?

check for turbo bits if the wastegate is ok

  • 2 years later...

UPDATE

i may have solved the problem, after just ignoring it the last few years, lol

is the attached pic the boost gauge sensor?

i found the hose had split at the end where it was connected to the sensor

so i cut the tip of the hose off, and reconnected it

before this, the boost gauge would read ~ 0 whether you were idling or giving it stick

now, it is reading almost -7 @ idle, and between half and +7 on boost

that seems better, right???

i also changed oil, oil filter, fuel filter, O2 sensor and air filter at the same time

seems to be running good now.

could that leaky hose have caused the problems described above (i.e. no boost)?

or was the car still boosting, and the gauge just not showing the right boost?

cheers all

post-13019-0-29672300-1411864196_thumb.jpg

post-13019-0-82099500-1411864209_thumb.jpg

post-13019-0-12318700-1411864218_thumb.jpg

post-13019-0-62436400-1411864272_thumb.jpg

Edited by Stooge007

I had the hose from boost gauge sensor to plenum split the other day. And wasn't showing boost on stock gauge. But I could defiantly hear something was not right as you could hear what sounded like a vacuum cleaner was in my engine bay when idling. Huge air leak.

Edited by dyl33

I had the hose from boost gauge sensor to plenum split the other day. And wasn't showing boost on stock gauge. But I could defiantly hear something was not right as you could hear what sounded like a vacuum cleaner was in my engine bay when idling. Huge air leak.

did it still boost normally, but just not show on the boost gauge?

or do you think it wasn't boosting as normal?

sounds like exactly the issue i had, and only found recently, lol

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...