Jump to content
SAU Community

Recommended Posts

The only thing I'm scared of is the clutch plate coming loose, 3 of the bolts stretched so I replaced them but I'm worried the rest might let go.

I'm trying to find a picture of how the wiring gets tidied up, I took photos on my phone when i pulled it out but it crashed and I lost them all.

Edited by lilcrash
  • Replies 886
  • Created
  • Last Reply

Top Posters In This Topic

Have been reading along since you started, just unable to comment as I haven't got a clue.

Gotta say man, hats off to your persistence. I can imagine how nerve wrecking it would be to be doing the assembly of your engine for the first time, so the fact that you've pressed on with it and not payed someone else to do it despite not getting any help from anyone here is quite impressive. I do hope it all goes well for you, hopefully those dog hairs don't cause any trouble laugh.gif

Ok this is all I have left to do/buy.

Engine mount nuts for the bottom side (don't know where they ended up), set of belts, 3 bolts in passenger side drive shaft, dump pipe bolts/studs, fuel filter, fit turbo oil drain, buy some hose for the cam breathers.

So yeah should be doing my mountain run on Friday night.

Brain fart again. My car has an imobiliser. F**k im stupid. Just warmed her up and went for a 100km drive though the country side. Got home and turned her off, realized I wasn't in the garage and it wouldn't start :/. Error 21 ignition signal fault, car started 10 times with this fault.

i just did what i read on the net, warmed it up with a high idle, checked for leaks (does have an exhaust leak at the cat to fix but i can do that anytime), then headed for the biggest hills around and loaded it up and down them until i had done 100km (wife needed to wee anyway) and headed for home)

im organizing with my tuner now to get it done asap, ive got my parents car to drive anyway so it can just sit and wait until a few more km are put through it.

my wife was watching the data logging while we were driving and nothing looked dangerous. it made 1-2psi once or twice up hills. although it feels like my hand brake is on, timing out maybe, the cas is lined up with the old marks so it cant be far off, if at all.

other then that, no weird noises or rough running

When I saw the guys do the timing on my car at the shop, they removed the coil pack from cylinder 1, put some sort of a plug from the coil pack to the spark plug then clamped the timing light to that line going to the spark plug. Has to be cylinder one, any induction light will pick up the signal through the wire to the spark and flash when it does.

Bond - yeah I thought that.

Sarge - I wanted to avoid pulling that apart before I changed the plugs for the tune.

I should hear back from my tuner tonight so il see what e wants to do.

Ok just did an oil change. 115km worth of driving

There is about 15-20 big pieces of something. And the oil has a generally glittery look. Millions of tiny particles. I've kept an oil sample.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Appreciate the feedback. It is street car, but not a daily. Last week I got a quote from a good exhaust shop for a decat, one which is bolt-on, bolt-off to be easily replaceable. I got quoted for around €150. I usually do push the motor, but I wasn't in this case to make sure that no damage is done until I get the cat sorted. I think it's best to also ask the exhaust shop for the other option and see what they can do. If (big if) I were to decat though, would it be best to tune the car or would the stock ECU handle it? As far as I know, the stock ECU is not tunable and that would require additional purchases.
    • As above, definitely bash it or get it replaced with a high flow unit.
    • get some flares on them, or wider guards haha
    • Another question sorry, what stainless do u use in the turbo external WG plumb back piping? Is it 321, 316 or 304?
    • Right, its been a while for updating this car, but I made some small but important progress today. In the end I bought an Ecutek dongle from the Australian distributor Tunehouse (for local hardware support) but have gone with a remote tune from Racebox in the US (because they have done millions of these, and I could not find any tuner where I could access the tune anyway as they are all password locked). The App is reasonably easy to work with, but the PC software reminds me of Haltech's ECU Manager that you need to use with the Plat Pro ECUs, it is a nightmare.  Anyway, I sent the details over, got back a tune file and a request for data logs. I finally got a chance to access a private test track today as they want redline logs in 3rd and 4th, and have sent them back for the first round of reviews. The main difference in the tune is going from 1.0 (stock) to 1.3 bar (19psi), although I'm sure is a lot of other stuff in the background. Keeping in mind this is a dead stock car with 125,000klm, this is what the App's performance test claimed: Before After Interesting to note that both 400m tests had the same terminal speed (158klm/h) but different ETs. And no, the speed limiter seems to be higher than that at 186kl/h. Summary of the key logged parameters for the 3rd and 4th gear runs were: Those little turbos were certainly whizzing at 200,000rpm+.  Also I'm really not that excited about oil pressure 55psi at redline so I think I'll go thicker than 5w30 (nissan recommend 0w20....) and see if that improves it. Other than that (and the big boost spike....) everything looks good as a start to me.
×
×
  • Create New...