Jump to content
SAU Community

Recommended Posts

Im potentially looking at a new ecu for my 34gtr, currently running power fc djetro but I want something that is a lot smoother. The 2 options I'm investigating are the haltech platinum pro and the vipec, both are plug in. I'm no ecu expert And would appreciate any input. I have ruled out the hka fcon pro because of cost.

  • Replies 48
  • Created
  • Last Reply

Top Posters In This Topic

running the original, Link G4 Plugin, fantastic ecu. I looked at the Adaptronic/Haltech options etc, but tuner (Trent @ Chequered) advised to go with the plugin, as did Rob @ RIPS. Also have flex-fuel setup with wideband as well, all good :)

What are the prices on each unit?? Haltech is quite a bit more isn't it?

The vipec I have found for 1650 (via online business) and the haltech theres one the forums here for 1750....if not normal RRP o both is 1850 and 2200 respectively.

Trouble Im having atm is that businesses i speak to are pushing the product i sell (which i would do if i was a business).

The thing I like about the vipec is the 4D map tuning for the GTR. Using TPS off boost and MAP on boost, to give it standard ecu like smoothness. Also has 4bar map sensor, antlag, launch control and flat shifting. Thing i dont like is you just get a board that has to be placed into a std case.

The thing about haltech is a lot more businesses are using this ecu. The fact you get a proper ecu and not a board.

Only had the pfc DJetro in for a day and not really a fan, just isnt nice and smooth to drive.

to my knowledge, the haltech has the same options that you have listed...

launch control, anti-lag, flat shiffting.

only comes with a 20psi on board map though, so extrat sensors will be required if going for big boost.

ive got a haltech pp in my 32, and couldnt be happier.

find out which has more support from tuners in your area, no good getting and ecu no one can tune.

oh, when i start and run my car, you wouldnt be able to tell it isnt stock.

if youre down near sydney anytime soon, and my engine is back in, pm me, and ill take you for a run...

good luck with either way you go.

wasted smaeshted spark.

ive tuned 900hp 6 cyl 6's with wasted spark, passed cars in botany with the IM240 emissions test with them also.

even tested wasted setup's with non wasted setup's back to back on same car, car did not even leave the dyno.

grab the vipec and you will never look back. just make sure you have a good set of coils. (splitfires would do you nice)

i was about to say, if your no ECU expert why ditch a proven setup thats worked on many cars?

there would be lot of djetro BNR34's out there id imagine and its all in the tune (and install) i suspect

particularly with twin map sensors and individual throttle bodies

get the tune checked before you bin a good working setup and fork out cash

theres no reason 1 ecu would be "doughey" and another isnt

its all how it is tuned

the only time youd expect a "doughey" ECU and not a "doughey" tune is if you lack load points, ie like a really nasty 8x8 ECU or something simple like that with limited tuning abilities

if the djetro PFC is setup properly and tuned correctly it should perform the same as the other ecu's

in the tune, as Trent was advising me to go the D-Jetro had i not wanted to go flex-fuel etc etc - D-jetro is more than capable.

Vipec is a rebadged Link, so they're exactly the same. I just preferred to buy direct from Link as they are Christchurch based and unfortunately lost their HQ in the earthquake :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • MR HAMMER has said his piece. Painted up to avoid Rusty Rusty. Actually lines up well. (i.e it lines up the same as the unmolested GTR guard). Turns out the GTR Strut brace does foul on the bonnet vents ever so slightly. May need a little bendy bendy if intended to keep using with a strut brace. So spacing it out to clear the FAST102 is not an option. Annoyingly, the bonnet vents also foul on the heater lines running over the engine. Given this engine does not EVER require a heater, a delete loop is going to be used. Don't worry, the defogger uses the AC. The heater is basically "Do not use the aircon and turn the fan on". It will still be effective, I promise.... once I get the system regassed... Will have to revisit with unvented bonnet I suppose, and suitable strut brace. There's plans to do this and other things tonight and bleed brakes (there was a weep) and put the bumper back on, and take Good Friday morning - Because troubleshooting on the side of the road limping it home at midnight tonight is ... not very smart.
    • Thank you all for you assistance. I contacted Nistune regarding the support for the RB20DE along with my ECU Code (23710-10U00). They do have a map for it and added the RB20DE as a purchasable option now as well. They also added Malta as a Billing and Delivery options as this was missing. I was honestly amazed at their quick response and action, it took less than 24 hours. I also looked again at direct fit options for injectors, just in case I were to replace them. DeatschWerks seem to use a Bosch EV14 base and makes ones that fit mine at 440cc lowest, but also have 550cc at the same price. I tried looking for other direct fit options and managed to find one (also Bosch EV14 based) which includes a plug and play adapter on ebay. Did a small test with a Noid Light on the troubled injectors and all seems good, so they are pulsing properly electrically. One weird part is that they are missing on the same two cylinders as before I got the injectors cleaned. Mechanic also found this weird as he did not label the injectors and it is unlikely to have the faulty injectors be installed in the same cylinders.  
    • Nice, let me know how you find the 98 tune
    • Put a hand on an injector and see if that's what the buzzing is. You might be triggering the injectors by moving off idle command.
×
×
  • Create New...