Jump to content
SAU Community

Recommended Posts

Hi,

Can anyone help?

I am after an "idiots guide" to these following numbers. I know its for changing the boost but it will allow you to change both?!

I appear to have put my manual "somewhere safe" and can't find it.

Thanks in advance...

G.

Link to comment
https://www.sau.com.au/forums/topic/38185-regarding-powerfc-boost-control-kit/
Share on other sites

The second numbers you have highlighted is the Duty Cycle. This is basically the amount of time the solenoid stays open (bleeds) in realation to the amount of time it is shut and allows boost pressure to the wastegate. It is expressed as a percentage.

The minimum you can set (from memory) is 10%, which would be sending boost pressure to the solenoid 90% of the time, bleeding 10% of the time - it would be used for low boost pressure.

The maximum you can set is 90%, which has boost pressure going to the wastegate 10% of the time and bleeding 90% of the time.

If the boost is spiking (I would put money on it in your case, those duty cycles seem very, very high for those boost pressures), you need to adjust the duty cycle down.

If the boost is lazy, or it isnt reaching full boost, you will need to adjust the duty cycle up.

If you change your boost pressure up, adjust the duty cycle up at the same time, if down, adjust the duty cycle down. The power fc has a self learning mode, which will optimise the solenoid actuation for optimum boost control BUT, if you are miles out of the ball park, it wont have a chance. For example, if I adjust my boost pressure up by .2KG, I usually adjust my duty cycle up 4%. then just monitor on the peak hold, if it is spiking (more than .1kg) I will adjust the duty cycle down by 2%. If it isnt getting to boost, I adjust duty cycle up by 2% at a time, until it is just spinking a little (less than .1kg) - from there I let the power fc learn for itself.

If you ever need a copy of the english manual (although its for an RX-7) one is available on line at he apexi usa website, look under electronics, then documentation or someting like that.

  • 2 months later...

Is it also true that running boost above 1 or 1.2 bar using 3rd party boost controller and PowerFC will cause your engine check light on the dash to light on, because PowerFC could not monitor the boost anymore? The only remedy is using the dedicated Apexi boost control option that connects straight to the PowerFC, is this true or not?

The 255 value is the 'learning value' isnt it?

Not quite sure what it corresponds to so I think it is more of an arbitrary value than anything else. I can tell when mine is learning cos you can see this value changing & then it stays put once it has learnt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lucky man, who owns it in the family? Any pics? 
    • The engine stuff is Greg Autism to the Max. I contacted Tony Mamo previously from AFR who went off to make his own company to further refine AFR heads. He is a wizard in US LS world. Pretty much the best person on earth who will sell you things he's done weird wizard magic to. The cam spec is not too different. I have a 232/234 .600/603 lift, 114LSA cam currently. The new one is 227/233 .638 .634. The 1.8 ratio roller rockers will effectively push this cam into the ~.670 range. These also get Mamo'ified to be drilled out and tapped to use a 10mm bolt over an 8mm for better stability. This is what lead to the cam being specced. The plan is to run it to 6800. (6600 currently). The Johnson lifters are to maintain proper lift at heavy use which is something the LS7's supposedly fail at and lose a bit of pressure, robbing you of lift at higher RPM. Hollow stem valves for better, well everything, Valve train control. I dunno. Hollow is better. The valves are also not on a standard valve angle. Compression ratio is going from 10.6 to 11.3. The cam is smaller, but also not really... The cam was specced when I generated a chart where I counted the frames of a lap video I had and noted how much of the time in % I spent at what RPM while on track at Sandown. The current cam/heads are a bit mismatched, the standard LS1 heads are the restriction to power, which is why everyone CNC's them to get a pretty solid improvement. Most of the difference between LS1->LS2->LS3 is really just better stock heads. The current cam is falling over about 600rpm earlier than it 'should' given the rest of my current setup. CNC'ing heads closes the gap with regards to heads. Aftermarket heads eliminate the gap and go further. The MMS heads go even further than that, and the heads I have in the box could quite easily be bolted to a 7.0 427ci or 454 and not be any restriction at all. Tony Mamo previously worked with AFR, designed new heads from scratch then eventually founded his own business. There he takes the AFR items and performs further wizardry, CNC'ing them and then manually porting the result. He also ports the FAST102 composite manifold: Before and after There's also an improved racing crank scraper and windage tray. Helps to keep oil in the pan. Supposedly gains 2% power. Tony also ports Melling oil pumps, so you get more oil pressure down low at idle, and the same as what you want up top thanks to a suitable relief spring. There's also the timing chain kit with a Torrington bearing to make sure the cam doesn't have any thrust. Yes I'll post a before and after when it all eventually goes together. It'll probably make 2kw more than a setup that would be $15,000 cheaper :p
    • Because the cars wheels are on blocks, you slide under the car.   Pretty much all the bolts you touched should have been put in, but not fully torque up.   Back them off a turn or two, and then tighten them up from under the car with the wheels sitting on the blocks holding car up in the air.
    • Yes. Imagine you have the car on the ground, and you mine away all the ground under and around it, except for the area directly under each individual wheel. That's exactly how it'd look, except the ground will be what ever you make the bit under each wheel from
    • Yes, if you set the "height" right so that it's basically where it would be when sitting on the wheel. It's actually exactly how I tighten bolts that need to be done that way. However....urethane bushes do NOT need to be done that way. The bush slides on both the inner and outer. It's only rubber bushes that are bonded to the outer that need to be clamped to the crush tube in the "home" position. And my car is so full of sphericals now that I have very few that I need to do properly and I sometimes forget and have to go back and fix it afterwards!
×
×
  • Create New...