Jump to content
SAU Community

Recommended Posts

On 15.01.2015 at 11:09 AM, froggy88 said:

My 03 coupe started to do this about 8 months ago. I don't recall what error code it was throwing up (something about a faulty sensor?) but my mechanic went through the whole system and couldn't find anything wrong. They also did the reset procedure and the light came back on after about a day.

I did the ECU reset procedure and it hasn't come back on since!

Sorry for bringing it up but that problem usually occurs after sweeping, vacum cleaning under front seats either driver or passenger or just moving seats back and forward. Well known issue that causes one or few yellow SRS connectors under front seats.

You must disconnect the battery before you try to do anything with any parts of SRS system. Check all yellow connectors under both seats, unplug them, clean them up, make sure proper contacts achieved in between every connector male/female and that is it, you'll never see that problem again. Sorry once again if it was sorted already.

* reason is the age of our cars and special material japs used to plated those contacts in yellow connectors.

@Nicko_2010 Thats not necessarily anything to do with under the seats. It could be any number if sensor or as you say wire issues. Mine was the clock spring even though the signal was a seat belt warning light and I did all the checks before I even took it to a mechanic. Unfortunately you need someone with V35 diagnostics which will tell you exactly where the fault is. Some people are quoting $150 just to do that my guy charged me alot less.

I had the passenger side seat warning light a few years back, I had tried cleaning the connectors several times, using contact grease to prevent corrosion, cable tying the wires in place so they couldn't move.. each time after a few months the warning light re-occurred.  In the end I removed the pins from the connectors and soldered the pins onto the wires instead of just the crimp.  that was years ago now and I haven't had another occurrences of the fault.  I have had the clockspring go bad since then, but that threw a driver side airbag fault code, which was different to the passenger side seat.

  • 5 years later...

Guys; having run into this problem again many years after I first encountered I found one method that absolutely works every time whether its the slow flashing light or the fast flashing light on the V35 Airbag warning light.

1. Turn the key to the On position (do not start), wait for the Airbag light to go off(7 sec). Turn the key to the Off position within a second of the Airbag light going off. (& before it flashes).

Wait 4 seconds then turn the key to On as above.

2. Repeat the above 3 times - ie total of 4 times. 

3. After the 4th time -when you turn the key to the Off position Wait 3 sec then turn the key On again. Wait for the light to go out. Then switch Off

4. Wait only 2 sec then turn On again. Wait for the light to go out. Then switch off.

5. Wait only 1 sec. Turn On again. Wait for the light to go out. Turn the car off. Remove key from the ignition. Then put the keys back in and start the car.

I have used the other 2 methods listed on this forum and Sometimes they work sometimes they don't. This one works without fail.

  • Like 1
On 7/6/2022 at 3:08 PM, niZmO_Man said:

how the hell do you discover something like that? Maybe the person who programmed it put it in a tech bulletin somewher

Yeah, possibly I read it somewhere years ago. But this time I just tried it without checking or looking. Also after you do these resets heaps of times you try anything!. A couple of sites do the 3sec then 2sec wait in the off position, so to me it just made sense to go that one step further!. 

On 08/06/2022 at 5:47 PM, sonicii said:

I tried this at least once & it usually works, but the last time it didn't. Thats why I tried the method above. I've never seen this before..Cheers 

It will only work if the fault that caused the light is no longer occurring.  This process doesn't actually fix anything, it just clears the current SRS codes.  If the fault still exists, it will just trigger the code again when the ignition is turned on next.

On 08/06/2022 at 6:02 PM, sonicii said:

It will only work if the fault that caused the light is no longer occurring.  This process doesn't actually fix anything, it just clears the current SRS codes.  If the fault still exists, it will just trigger the code again when the ignition is turned on next.

Yeah I know. So far so good though..

I had the exact same thing happen to my 96 R33 GTST. I tried the steps above and it only slowed down the blinking. I did find another method and it fixed it, even after starting the car several times after the fix. These steps are as follows:

Leave the driver door open when doing this. Put the key in and turn it to the ON position, then quickly press the door jamb button 10x. Turn the key to the OFF position, wait 3-5 seconds and then start the car. The airbag light should go off completely. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • GTSBoy on your suggestion on another thread I had a look at those injectors and ended up getting them because of the quality.  Got the expensive ones.  
    • Hey guys been looking everywhere to try and find the correct gtr hood latch support part number but only found the first half and when I search with that number it sends me to an r34. The first part I found was 62515. If anyone could help me with the rest then I’d really appreciate it. Or if there’s some alternative hood latch support that would work even better cause I can’t find any for sale. (Searched on upgarage, partsouq,buyee,rhdjapan) 
    • If you've only done the upper control arms on the rear, AND you have changed their length (by more than about 1mm) to set the camber you want, then you will definitely need/want to install traction arms also. Adjusting the camber arms on their own WILL introduce bump steer and make the car unpleasant to drive. Most owners have no idea that their car could behave infinitely better than what they put up with. I'm not entirely sure what the Stageas need, but I am thinking that unless you have massive front spring rates and pretty soft rear springs, you have waaaay too much rear bar. Oversteer city, in my estimation. Combined with possible excessive bump steer from maladjusted arms, that could be a recipe for nastiness. ATR43SS2 is not a highflow. It is an outright replacement turbo. It's a little bit bigger than the largest highflow profile that Tao does. Probably a solid 300rwkW turbo where the bigger highflows will be about 30-40rwkW less. Nevertheless, we're only talking about ~300 rwkW, which is well within the abilities of the stock ECu to run with a Nistune on board. I would do so without hesitation - and I will be doing so when I get my finger out and actually get the injectors and AFM installed. But, if you would prefer to drop a whole lot more money on the ECU side, then I suspect you're looking at Haltech. The Haltech fanbois here will all spout on about all the available engine protection you can have, that you can't have with the Nistune option. And they're right. But it doesn't really come for free either. You will spend more money on extra sensors and the like, plus the work to install them. If the engine was built and therefore represented a big investment to protect, then I'd say definitely do it. If you view the current (and forever into the future) shortage of replacement engines as something to prompt similar protection, then also, do it. If you see a destroyed RB25 as an opportunity to put in a Mercedes or other V12 (like I kinda do)... then your perception of the risk/reward might differ. These are good injectors. You can also get a "better" set of the same with more flow matching, for more $$. 1000cc is where you will want to be. You will need an R35 AFM and adapter tube if you want to stay with Nistuned stock ECU. Otherwise, if going Haltech, you can ignore. As for intercooler. Just about anything will do. You're only talking about ~300rwkW. Just put a big core in there. Be aware that return flows do add significant pressure drop and will cost power and will make the turbo work harder to achieve the same goals. If you can manage a proper crossflow, do it. I'm keeping my very good return flow because I'm only expecting to be in the ~250rwkW range, and will live with whatever outcome I get.
    • I have a heap that i have collected if you want some authentic ones still. Pm me if your interested!
×
×
  • Create New...