Jump to content
SAU Community

Recommended Posts

Hey guys,

Got some things I really don't need lying around:

2 x R32 Tail-lights (White Surround, Ie Both Sides) - $150

2 x R32 Windscreen Wiper Motors - $25 ea

1 x Passenger R32 GTSt Seat (On Rail) - $120

1 x R32 GTR handbrake - $10

Various Interior parts:

- Centre Console - $50

- Part that goes around the dash cluster - $10

- Part that goes around the centre console - $10

1 x R32 GTR ABS unit - $200

1 x R32 GTR Alternator - $100

1 x R32 GTR Starter Motor - $100

4 x R32 GTR standard Suspension (full set) - $300 ono

Give me some ballpark figures. You know what most of these parts are, but if you are interested I could get pics. Some parts may not be suited to freight.

Thanks,

Rick

Link to comment
Share on other sites

Hey guys,

Sorry about the delay, I have been busy.

Its not the panel that goes around the gearbox surround and up around the cluster/gauges/stereo. It goes BEHIND the dash, if you look at your interior side on you'll see a panel going toward the front of the car, on both sides of the middle of the dash, and thats it :D

You might have a boost controller or a turbo timer or something stuck to the side of it..

lwells: Sorry, don't have them :)

Nismo_286: Yep, got that complete in one piece, $50 :)

Link to comment
Share on other sites

NickySantoro, do you have the part number of the ABS system on a 33GTST ? Knowing Nissan they'd be the same, but it'd be good to be sure.

CerealKiller, the condition is average, a little bit of wear but its not really peeling off. Looking at the windscreen wiper motors, I've got 1 x front and 1 x rear, so this one is avail to suit yours if you want :mad:

Link to comment
Share on other sites

  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
    • You can just get the injector bosses, which allows top feeds to fit. He can use the same injectors without issue, like these (another option): https://rocketindustries.com.au/af59-2210-rb25-fuel-injector-inserts     The Racework ones look a bit better: https://www.nzefi.com/product/raceworks-lower-injector-mounting-boss-kit-for-r33-rb25det-s14-s15-sr20det/   You could also just get a similar kit like the Radium one by Plazmaman: https://plazmaman.com/product/nissan-rb25det-r33-billet-fuel-rail/?srsltid=AfmBOoogfYq49X0fu2Wdbf8yOf6zt9egyPAif_gn3Qr3G8hzAphhTgOkO70  
×
×
  • Create New...