Jump to content
SAU Community

Recommended Posts

NGK Bcpr6es 0.8 I gapped em to 1.1 n that didn't help on that problem but ran better cause I got new coils so dnt see the point of gapping...should I try diff plugs cause alot on here use them. but had read on here saying the bcpr are for rb20?maybe oil is to thick cause I'm running 15/50 cause I'm up 2500km on this oil,,,maybe the oil taking ages to warm up?

Im using PFR5G-11 but its a NA.

I doubt its oil my engine is using 10w40 and still does it and is in A1 condition after replacing almost everything now.

Also if it was oil causing something like this, the lifters would tap there heads off early morning because not enough oil would be reaching the head.

Just cant understand why when i tap the accelerator is fixes itself or if i let it stall the 2nd start is perfect.

  • Replies 44
  • Created
  • Last Reply

Top Posters In This Topic

Mine does exactly the same thing r33 series 2 GTST... Idles rough at first start up then u give it a tap Pryor throttle and it's fine....

My car is stock as a rock bar the 3inch exhaust...

I have noticed since i changes the oil that it has stopped happening... Though it is starting to warm up during the summer months so not sure how much that would effect it....

Mayb try a afm-less start next time and see if it does it on the limp map?

i tried this today but nothing changed.

Over the last few days i have also been holding the clutch in when cold starting. Its been starting good.

Could someone have a few goes and see if it helps them....

Yea I'll give it a go tonight when Its dead cold if I remember

The whether has been sh#t cold here at night so will be a good test

I tried it again but its still doing it. Holding the clutch in is just causing it to not stall as easily but the longer the car is left the more worse the start is. After 24 hours its a guaranteed stall.

cheers

My car still does this. Sometimes it dies out the first start then second time its perfect but on occasions it will fire up first time after a long cold, and after about 3 seconds of 300 rpm.

The response from that other chap on page one got me really puzzled, all brand new parts etc and its still there. I'm used to it because its done it for long enough but it is still something that shouldn't be happening so I'd like it gone.

My car still does this. Sometimes it dies out the first start then second time its perfect but on occasions it will fire up first time after a long cold, and after about 3 seconds of 300 rpm.

The response from that other chap on page one got me really puzzled, all brand new parts etc and its still there. I'm used to it because its done it for long enough but it is still something that shouldn't be happening so I'd like it gone.

Yeah i dont exaggerate about all the parts i have changed, only because i work for nissan parts i could afford to do it.

CAS and fuel presure reg are the only things left, everything else is new. I only care if i sell my car because it makes it look crap but its really almost showroom. Everyone that sees it thinks its done less than 10,000km.

Seems to be a common problem and dosnt matter if its a NA or a turbo by the looks of it.....32 and 33 aswell

I have tried priming it but it does nothing.

Edited by central coast person

Have u guys tried disconnecting the coolant temp sensor? Im curious to see if there is too much fuel on cold start and the throttle needs to be pressed to lean it out a little.

Central coast person, what series is ur engine. I might be able to plug in a nistune to ur car and see if i can sort the cold start issue out or not

Sarge try taking fuel out of the under 10degree area(or wherever the temp is sitting) before u start it with the coolant temp sensor connected.

Hey DVS,

I brought a new coolant temp sensor but it did nothing . Wiring and conector are also fine for it....

Car started up rough as all hell today as its cold and rainy on the coast.

When it starts up rough it splutters like a drag car with lumpy cams and yes if i tap the accelorator it definatley is leaning the car out as it idles like a brand new car the second you feed it more air or if i start the car with my foot on the accelorator pedal pushed in about 2-3mm, it starts like there is no problem at all (i dont like doing this though because if my foot is down more than 2-3mm it rev's the shit out of it on cold start). I dont imagine this problem to be good for a cold start aswell as it stalls and idle jumps around for about 5 seconds so either way its a lose, lose situation.

DVS if you can check it when ever you want, it is a series 2 engine.

Excellent. I have a series 2 nistune in z32 ecu inmy drifter so i can use that to see if i can get the cold start right on ur car.

What i meant with the coolant sensor is to trick the ecu to think the car is warmer so it wont add as much fuel on cold start to see if it helps.

Might be the other way though and need more fuel.

Trial and error

Excellent. I have a series 2 nistune in z32 ecu inmy drifter so i can use that to see if i can get the cold start right on ur car.

What i meant with the coolant sensor is to trick the ecu to think the car is warmer so it wont add as much fuel on cold start to see if it helps.

Might be the other way though and need more fuel.

Trial and error

Tastey.

I think i gave that a go a while back, cant really remember. I'll give it a go after work that will be enough time to cause it to start up like that.

Where and when would you be able to try the ECU out?

A lot of post on the NET with this problem on skylines and not one has a fix

Edited by central coast person

Hey Guys, this might not be helpful at all but my car does this too and today i tried something different. I didnt let the fuel pump prime and the car started fine.

May have been a slight studder but way better than usual, but my car is stock so don't know if it helps. No mods stock ECU.

Could have just been a fluke but might be worth a shot and it backs what DVS is saying about it being too rich (too much fuel at startup). The Fix who knows lol

I keep trying different things every time I start the car up. Holding the clutch down SOMETIMES makes a difference. Today I went to pull fuel out but had no idea how to do that(under the correction table for water temp? Which column on the HC?). In the morning it was sitting on 29C water temp, the car fired up first time. I'll try the quick start tonight although it might not work because my piece of shit alarm takes about a second or two to let my ignition come on after the key is turned, piece of rubbish. Its not enough time for me to check my wideband to see any output so its no help.

My car done this when it was stock as as it could be, bar the exhaust and cooler. It does it now with everything I got on it(turbo, injectors, ecu, fuel pump, afm etc). Spark plugs don't do shit. I got brand new oem coils with brand new plugs, no change. Done it with my old plugs, done it with my yellow jackets, with my old coils. It must be an air to fuel thing. Maybe Ill get someone to start the car for me while I sit near the exhaust and see if there is a rush of unburnt fuel smell.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Which are almost all nonsense. Ignore. Obviously enough, if it is not a porous block, then any such thing is a waste of time. External block surface? Would be a waste of time, if the block was actually porous. It would need to go on the inside, which is inaccessible, and even if the block was open deck so that that area was acessible, it would be unlikely to work. But seeing as this is all nonsense, stop worrying about it.   If the coolant is coming from the side of the block it is 10:1 odds that it is either a welch plug, or it is coming from the head gasket. Maybe from one of the coolant lines feeding the turbo, or even the heater. Liquids that leak from up high can travel sideways along casting surfaces or pipes, etc on the engine before finding a spot from which to drop.
    • Yeah rust is sadly also a bit of an issue on my car. Doubt there is many cars out there that actually have no rust in those aeas. The strut towers look fine but some of the surounding metal sheets show a bit of brown cancer peeking out from in between. I hope I can make do with external remedies and won't have to rip open the whole front end anytime soon. It looks somewhat minor compared to some shit I have seen online. I have worked on a few cars but I expect the RB26 to be my first 'engine out' job at some point.
    • Welcome Jan, It's very likely that you are in over your head. You'll just have to learn to swim hard and fast! These old rust buckets have more ways to bankrupt us than almost any other car. But hopefully there's nothing wrong that ruins the whole show! We can help a fair bit. There's plenty here who've been fixing these things for >25 years. cheers
    • Hi all. First off, thanks for reading my post. So end of last season I put the car away knowing I was leaking at least two fluids. One of them being rear turbo's oil. I went to my car recently that is waiting in a garage to take a peek with my boroscope to try and see if I can narrow down the souce of oil before taking it out of storage. What I found is not so great I think. The rear turbo is (probably) leaking from the oil drain. The hose and it's clamps are probably the original ones, so most likely just worn out or loose. However I spotted a line of rust going straight down from the turbo oil feed, as if water leaked out of there at some point. Also explains the red liquid that was dripping from my front subframe, which I initially thought was power steering. I can even see coolant drops hanging off the side of the oil pan as well. After a quick hit on the web I found a select few discussions about porous engine blocks. My question is if the pics of the turbo oil feed and the left hand side of the block (imgur link below) looks like it could be exactly that to you. Maybe someone in the community has seen it before and knows what it looks like. If it actually is a porously leaking block, has anyone attempted at fixing it with simple methods like putting a sealer in the cooling system and using something like jb weld on the block surface, or will it just leak in 2 weeks again? I could not find any detailed info or pictures on this topic. If I need a new engine, tell me softly. https://imgur.com/a/knVvmZ8
    • Hey all. I'm 23 and from Germany, September last year I bought a mildly modded 1995 GTR Vspec. Looks great and was fun so far, but I already have a list of issues of various severity that I need to take care of, potentially growing longer the closer I look. I just hope I'm not in over my head, I really want to keep the car and work towards it becoming great. I hope y'all will help me out in getting there, I am positive I will need help sooner rather than later to figure out how to proceed. greetings, some pics of the car I posted to imgur. https://imgur.com/a/StKkabz
×
×
  • Create New...