Jump to content
SAU Community

External Venting Wastegate And Exhaust Flow

Husky33

By Husky33,
in Engines & Forced Induction

 Share

Recommended Posts

Husky33 Veteran

Husky33

Posted
Posted

Hey

Just wanted to get some info on how an external wastegate that's venting to atmo will effect the ability of the exhaust to flow

more gasses.

For eg.

The more power generally the bigger the exhaust. I know a 3.5inch exhaust is usually recommended for power levels around 350rwk.

However if you had 350rwk with a 3inch exhaust and a external venting wastegate, will that flow similar numbers to a 3.5 inch exhuast.

In my instance it will most likely be a 3076r .82 on e85 running around 20-22psi, with a 44mm external gate. Exhaust is a 3inch dump/front,

decat pipe and 3inch titanium catback.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

Track only car? Otherwise illegal unless you run it all the way to the back in which case you may as well just get a bigger exhaust.

And to answer your original question at full boost just before the w/g opens its all going down the exhaust pipe anyway

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

I proved this relieves a somewhat restrictive exhaust. My old S13 when it had a gt28rs i put on a 50mm wastegate with screamer and gained alot thought the revs and 20kw up top.

This was with a sr20 and a .63 rear housing.

And aslong as the wastegate plumbs in before the cat it should be "legal".

If u plumbed it in further past the cat it may give u the gains u want, by then the exhaust pulses have started to cool and there is more room available

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By The Bogan · Posted

      I have engineer in my job title One of or motto's though is "we make and we break"
    • GTSBoy
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By GTSBoy · Posted

      This is actually 2 whole different trains of thought that need to be addressed separately. No, as Matt says above, "Engineer" is not a directly protected title. A lot of guys who just do mechanical design via CAD, with or without even some sort of associate diploma in engineering, often have the job title of "Design Engineer". A train driver can probably still describe themselves as an engineer. But, to usefully get employment with anyone as a proper engineer, you're going to have to have at least the necessary and relevant degree qualification. You're not going to get a job as an electrical engineer if you have a chem eng degree, unless you can demonstrate x number of years of working in that capacity, sufficient knowledge, etc. Having the degree is at least in indication that you've seen the relevant text books, even if you haven't read them (like pretty much the last 10 years of graduates!). To be a self employed engineer.....you could get away with quite a lot pretending that you're suitably qualified, without actually being a proper engineer. But, you will find yourself unable to work for a large section of the client space because a lot demand CVs and capability statements when considering contracting for any engineering work these days. Insurances too. If you're not a proper engineer, it will be much harder to obtain proper PI insurance. Insurance companies have gotten hip to that. The "Professional Engineer" thing is a thing in Australia. If you have the right qualifications and experience you can apply to the relevant engineering top level body (mostly Engineers Australia, the less said about whom, the better), to be assessed and approved as a Chartered Professional Engineer, CPE. There are high bars to get over and a requirement for CPD to maintain it. The RPEQ thing is similar-ish, in that you have to demonstrate and maintain, but the bars are a little lower. It is required to be RPEQ in order to sign off as an engineer on any engineering design in Queensland. The other states haven't fully followed suit yet. There's "engineering" and there's "engineering". Being an engineer that signs off on timber (or even steel) frames for housing projects, council creek crossing bridges, etc, is a flavour of civil engineering that barely warrants the name, description and degree. That would be soul crushing work anyway. Being an automotive engineer working in the space where you have to sign off on modifications to cars and trucks would also be similarly soul crushing. At least partly because of the level of clientelle, their expecations, depths of bank balance, etc. And that brings us to your second question. No, we do not have professional engineers "do vehicle inspections". Well, not the regular roadworthies, etc etc. That's done by mechanics. There might be some vehicle standards engineers at the various state govco inspection stations where cars go to get defects cleared and so on, but that's because they (the cars) are there specifically for defect inspection and clearance and so the stakes are a little higher than on an annual lights and brakes working check. But, if you modify a vehicle in Australia, you have to get it engineered. A suitably qualified (and effectively licensed, which I will get back to) automotive engineer will have to go over the application, advise on what would be required to make the mods legal, supervise some parts of the work, inspect and test the results, and sign off. The "licensed" aspect comes from there being a list of approved engineers to do these things in each state. They have to jump through hoops set up by the govco vehicle standards divisions that mean only the suitably qualified can offer to and approve such mods.
    • MBS206
      My BMW E39 528i touring

      By MBS206 · Posted

      It's got a problem Prank... It looks like both washer spray caps have fallen off this car... 😛
    • GTSBoy
      Should I use rust converter on this?

      By GTSBoy · Posted

      Meh, it's only got to last another 10 years or so until you'll be forbidden to drive it. Keep it dry and forget about it.
    • MBS206
      🚨 Need Advice! Overcharged for Engineering Report 🚨

      By MBS206 · Posted

      The title of Engineer is not protected. However different states have different rules about what an Engineer requires to operate. Engineering for a motor vehicle modification is very different to engineering for a bridge, electronics, etc, including what that engineer needs as certifications.   In Canberra, "Engineer" is the loosest category with basically nothing stopping you calling yourself and engineer and designing a bridge or building. From what I've reviewed, QLD has the strictest requirements through RPEIQ.
×
×
  • Create New...