Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Looks a little high, but that is not how Nissan gauges work. Basically all Nissan temp gauges will warm up to their normal running temperature, and sit there until the fluid actually boils (and you have broken something), and only THEN goes off the richter scale hot. Generally they don't move much inbetween.

But you should put a real temp gauge on every Nissan car imho - espeically one with a 95-100 degree warning light. Boiling cars is the 2nd easiest way to blow an engine (next to not enough oil/low oil pressure).

I put an awesome EL overlay over my cluster, and in the process of fitting it put my temp gauge out of scale - mine now sits between the 3rd and 2nd last lines when at operating temp (and already 1/3 way up when cold at start up). That's why I put in a real temp gauge

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Gosh...I and my mech didnt pickup this overheat issue when we do inspection before buying. Now it becomes annoying....

Do you guys think i should go back to Nissan dealer to have diagnosis checks? Or anyone can recommend any reliable mech in Brissy?

Thanks for you guys help~

or just check the fluid level so that you dont pay someone $180 to top up the radiator......

Did check fluid level is full & top water hose is not too hard to press, fan is only running when a/c is on but even a/c on, the temp is keeping in above middle line...what eles i should check by myself?

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Just found your question when i was a bit panic, sorry, mate~

I havent flush the coolant yet, but will do soon.

What do you mean by "doesnt have air in the system, look for a blockage" how to check it? I check my fan only runs when a/c on but it doesnt go back to normal temp even with fan (a/c on) on or when i am cruising again.

Water pump issue? What other procedure that i can check whether it is water pum failure? Pls advise, thanks~

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

Thanks, Andrew. How can you check air in your system?

Unscrew the little plastic bleed screw in the left hand side at the rear o fthe engine. If you look along the water piping you will see it - it is black plastic and has an X in it to unscrew it with a phillips-head screwdriver.

Hi Mikhail, so have you ever checked by Nissan or any V35 SERVICE SPECIALISTS before? Or you just leave it as it is?

I am leaving mine as is as I am pretty certain its normal. I think I saw a similar thread on here that said the same thing. I had mine serviced and no problems were found. Also my needle is just below the middle, yours is above middle.

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

I wrote a proper bleed procedure somewhere on G35, just search my name.

Also get a radiator cap with temp control gauge on it, you can go check yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The fact that Hypergear has been posting here for like 10+ years would 100% make me go to him for a turbo upgrade. Glad you got what you wanted from them.
    • I second this motion. GTSBoy you need to start posting vids man.
    • Yep that sounds like a scam. Avoid that company if you can.
    • Mate. Your car is like 20 years old. Expect that the rubber bits (seals, hoses, etc.) needs to be replaced. Best bet is to carefully go through your engine bay and try to find parts that need replacing (e.g. rubber hoses). for your power steering issue, best bet is to pull off the pump (not that hard, you can buy basic tools from Supercheap et. al. to remove it) and then inspect/get it rebuilt. *edit* forgot to add, no idea on R34, but my R32 HICAS computer has been playing up since I bought it (10+ years ago), so I just disconnected the small plug to "disable" HICAS but keep my power steering. So something extra for you to look into.
    • Something to keep in mind, RB26DETT was dreamt up in 1986-1987 for the Group A regulations. So to compare it to a post-2005 engine is not the best. You must Compare the RB26DETT to its contemporaries, like the YB (which it killed off), the 1GG, 1JZ, whatever 5L V8 Ford/Holden had, etc. etc. aka late 1980's tech. When you're trying to match RB26 to a S58, you've gone off the deep end already and are looking at custom block/head/etc so no longer a standard engine. Technology has come a long way from 1990 to 2020.
×
×
  • Create New...