Jump to content
SAU Community

Recommended Posts

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Looks a little high, but that is not how Nissan gauges work. Basically all Nissan temp gauges will warm up to their normal running temperature, and sit there until the fluid actually boils (and you have broken something), and only THEN goes off the richter scale hot. Generally they don't move much inbetween.

But you should put a real temp gauge on every Nissan car imho - espeically one with a 95-100 degree warning light. Boiling cars is the 2nd easiest way to blow an engine (next to not enough oil/low oil pressure).

I put an awesome EL overlay over my cluster, and in the process of fitting it put my temp gauge out of scale - mine now sits between the 3rd and 2nd last lines when at operating temp (and already 1/3 way up when cold at start up). That's why I put in a real temp gauge

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Gosh...I and my mech didnt pickup this overheat issue when we do inspection before buying. Now it becomes annoying....

Do you guys think i should go back to Nissan dealer to have diagnosis checks? Or anyone can recommend any reliable mech in Brissy?

Thanks for you guys help~

or just check the fluid level so that you dont pay someone $180 to top up the radiator......

Did check fluid level is full & top water hose is not too hard to press, fan is only running when a/c is on but even a/c on, the temp is keeping in above middle line...what eles i should check by myself?

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

bleed the system, might need topping up. at that needle position youre probably looking at around 110-112degrees water temp. not the best, but is still operational.

if it doesnt have air in the system, look for a blockage, or check the status of your thermo fans. does it go back down when youre cruising again? if it doesnt, possibly a water pump issue.

Just found your question when i was a bit panic, sorry, mate~

I havent flush the coolant yet, but will do soon.

What do you mean by "doesnt have air in the system, look for a blockage" how to check it? I check my fan only runs when a/c on but it doesnt go back to normal temp even with fan (a/c on) on or when i am cruising again.

Water pump issue? What other procedure that i can check whether it is water pum failure? Pls advise, thanks~

Your thermo fan should come on even when the a/c is off, once the car gets hot enough.

I would be checking for air in your system (which I bet is the cause). Or get a mechanic to install a water temp probe and actually check your water temp to see if your stock gauge is lying/broken.

Thanks, Andrew. How can you check air in your system?

Unscrew the little plastic bleed screw in the left hand side at the rear o fthe engine. If you look along the water piping you will see it - it is black plastic and has an X in it to unscrew it with a phillips-head screwdriver.

Hi Mikhail, so have you ever checked by Nissan or any V35 SERVICE SPECIALISTS before? Or you just leave it as it is?

I am leaving mine as is as I am pretty certain its normal. I think I saw a similar thread on here that said the same thing. I had mine serviced and no problems were found. Also my needle is just below the middle, yours is above middle.

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

If you have access to someone with a datascan tool, get them to check the coolant temperature with it, if it is around 85-90 deg C, then I wouldn't worry about it. Especiallly if it doesn't seem to go up and down when driving hard, or climbing hills

I wrote a proper bleed procedure somewhere on G35, just search my name.

Also get a radiator cap with temp control gauge on it, you can go check yourself.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ahh...should have been clearer ~ there's 2 ... SMJ = super multi junction (connector)...   ...this is connector 6 & 25 in above image -- body harness to engine loom (6) & body harness to main loom (25) Headlights go to front via connector 6 ; fuel gauge goes to tank sender via connector 25  ...like I say this is R33 diagrams, but at a pinch R34 won't be too far different. *IF* the two ground faults are related, this can be the only place where both wires converge (as one runs to the back, the other to the front)... ....thing is, you probably need to establish if the faults are related (unless you examine that area and find obvious chaffing on the looms there to body ground)....*IF* the fuel gauge is still broken (full needle deflection), I'd be headed for the boot, remove fuel sender wire, key on and measure the voltage there ~ it should be roughly 10volts. If that's ok, check sender to ground resistance...if this is a dead short to ground (and there's fuel in it), then sender has failed or something funky has happened to wiring in the tank. edit: ahh...rereading the thread, this is R32....above fuel sender test still valid tho'
    • I just changed the timing belt on my RB25DET NEO and wanted to get some opinions. I’ve been super cautious, did a lot of research, and took my time. I’ve driven the car, and it runs fine. After warming it up, I revved it to 8000 RPM a few times—no issues, everything held up.   After the drive, I heard a noise that I think is either the clutch or possibly a tight accessory belt. It’s not constant, just comes and goes.   I took the timing cover off to double-check everything:   Belt is on properly, Tensioner is tight, Did the 90-degree twist test—belt isn’t too tight or too loose.     What still worries me is that I noticed the belt seems to sit a little toward the front edge of the gears, especially on the idler pulley. It even looks like it’s slightly coming off the edge there. Is that normal?   My old belt (5 years old, ~3,000 miles) also showed a bit of wear on that same edge, so maybe it’s just how it sits? I’m probably overthinking this, but since it’s my first time doing this on a NEO and the engine is forged, I really don’t want to mess anything up.   Also, I’m thinking of swapping to a clear front timing cover with the glass window. Would you recommend NITO or HPI? HPI looks reputable and their covers have 2.5mm thickness, but not sure if there’s a real difference between the two.   Any advice or reassurance would be much appreciated!
    • 40 grit sounds about right, to start. You make some decent cuts/damage in the coating with that, then rapdily scale up to maybe 80 and 120 for the bulk of the actual removal, then fine it off to 180 or 240 perhaps. No need to go any finer than that, and maybe no need to go even as fine as that. Wrap it on a big block and have at it. At least on the hub face.
    • Do the GKTech rear lower control arm mount relocation, and either alloy subframe inserts or very stiff subframe bushes. Traction is going to be at a premium!
    • Hello,   My name if Frederick, i'm 30 years old and I live in Belgium, Europe! I used to have a Nissan 370z daily but since I got a company car I turned that into my seattime driftcar. About 3 years ago I also wanted something older with more feel, so I got an R32 GTST with an rb26 engine. I am now getting the rb built to have around 800hp and it's close to being finished. I'm very excited for how it will drive and how driveable it will be! Regards, Fred!
×
×
  • Create New...