Jump to content
SAU Community

Home Made Car Ramps

ms33

By ms33,
in Fabrication

 Share

Recommended Posts

ms33 Enthusiast

ms33

Posted
  • Author
Posted

I used this from the other forum for getting the angle correct, mine from the wheel to the front of the bumper is 32" unlike his 25".

Basically, measure the height from the front bumper to the ground then the distance from the wheel to the front of the bumper. Mine is 25" from wheel to front, and height was 5-5.5", used 5" for safety. So, with these figures you know the angle (for ramps) which is 10.7 degrees. But you know the front must travel at least 25", before hitting anything over 5". Each step is 13" long, and the height is 1.75".

Based on 1.75" per step, I know 2 steps =3.5", but 3 would be 5.25". So based on the height from my bumper to the ground of 5", I know that the 3rd step must be over 25" away from the 1st.

In theory top one could be shorter and if the height was 5.5" then i could climb 3 steps every 25", instead of 2. And the step could be 12.5" instead of 13". Therefore the ramps overall can be shorter. But I just played safe (ground wasn’t exactly even at measurement).

Conclude for shorter ramps: stopper = 1.5" long, top step = 14", next step = 26.5", next step = 39". Next step (could be final step if only require just over 7" in height, I found this sufficient) 51.5", if not next step is 64". Each platform has 12.5".

And the shopping list:

I bought 3 lengths of 47mm x 250mm x 4.8mtrs of sawn wood from Covers.

1st length 2 x 1380mm and 2 x 920mm

2nd length 2 x 2300mm

3rd length 2 x 1840mm and 2 x 460mm

They will cut all this for you.

That'll give you the 10 lengths you need to make the 2 ramps.

And a box of 10 x 75mm screws.

This is all assuming you have at least 5" clearance from your front spoiler to the ground. If less you'll have to re-calculate.

Hope this helps. icon_thumright.gif

Link to comment
Share on other sites
W0rp3D Grand Master

W0rp3D

Posted
Posted (edited)

and if you want to take it one step further you could extend the length so you could get the whole car on there and have a stand under each wheel and remove the centre bits, closest you will get to a hoist with out spending lots of cash!

Edited by W0rp3D
Link to comment
Share on other sites
n/a_neo_r33 Enthusiast

n/a_neo_r33

Posted
Posted

and if you want to take it one step further you could extend the length so you could get the whole car on there and have a stand under each wheel and remove the centre bits, closest you will get to a hoist with out spending lots of cash!

thats a wicked idea :cheers:

Link to comment
Share on other sites
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      RB gearbox options

      By TurboTapin · Posted

      What makes you say CD009 boxes are not as strong as you would think? I've always been told the last revision (CD00A) is good for 1000whp and I have no issue's believing it when comparing one side by side with an RB25 box. Makes them look tiny. 
    • OO Dan OO
      Nismo 1.5 way Stub axle issue

      By OO Dan OO · Posted

      I picked up an open Center with shafts. I was told the Open shafts will fit a mechanical LSD and looking at them. I think they will work. Will update 
    • OO Dan OO
      Nismo 1.5 way Stub axle issue

      By OO Dan OO · Posted

      The manual says a lot about the different ratios requiring different shafts. all the Centers are the same but depending on the ratio, this determines the shafts because different ratios need the center to be offset more or less or right to left.
    • r32-25t
      Nismo 1.5 way Stub axle issue

      By r32-25t · Posted

      those 2 sets of shafts will not interchange and if you’re lucky you haven’t damaged anything with all your pressing and bashing you said you’ve done 
    • TurboTapin
      Lets play a game - What is causing my oil consumption?

      By TurboTapin · Posted

      Freshly built stroked RB25/28. Motor runs great but consumes a lot more oil then It should. This summer with the heat I was consuming roughly a quart per 1800-2000kms. Now with the cold weather coming in, I'm consuming a quart per 1000kms which is no bueno. I had originally chalked this out to break in taking a little longer then it should, but I'm now around 4000km's on this engine. I think it's fair to say something isn't quite right. Here's the kicker, can't find what's causing it. I've also spoken to my engine builder and Precision Turbo and can't figure it out. Here's my train of thought on possible causes and what I've done.  Precision Turbo - I originally started thinking my oil pressure might be a tad too high for my 6466 Gen2. I took the center cartridge out, and while yes there's signs of oil on the turbine heatshield, it's very moderate. There's also very minor in/out play that concerns me. I sent pictures and videos to precision and they said the residue and in/out play is minimal and they doubt this is the issue. For piece of mind, I went ahead and installed a Turbosmart OPR V2 to bring oil pressure down. Made no difference. Precision is willing to take it in on RMA for an inspection and I'll probably take them up on that offer for peace of mind. BTW. Is it just me or does the turbines inducer's look clipped and not even between each other? I just noticed this now while posting and looking at the picture zoomed in. Might just be the picture...  Rings - Hot compression test and leak down test look good. Compression is 160 +-2psi across the board. I leak down at 16% on cyl 1,2,3,5,6 and 18% on cyl4. Keep in mind I have a snap on leak down tester and they read high (I.E, 15% on my wifes 2018 Sentra with 70000kms). Sparkplugs show minimal oil (Only #4 seems to have a tad). At a quart per 1000km's though, I would be expecting them to be wet. Here's the kicker, I run WMI. I'm thinking what if my compression rings are great, but I have an oil control ring issue on cyl4 and my WMI is steam cleaning the pistons and sparkplugs? I can still see the "Spool" logo on top of my CP pistons. The only time I see smoke out of the exhaust is in the high rpm/load range. So far, this is my main culprit. I'll probably turn off my WMI and go out with the car at spring pressure tomorrow and repull the plugs. Other thing that's strange though is that I have never seen any oil in my catch can. Thing is still dry after 4000kms. Cyl1 - Left, Cyl6 - Right. Valve seals - They're new and I would expect oil consumption on idle, first cold start or during decel. None of which is happening.  Crankcase pressure - I have 2x 10an valve cover lines to a vented catch can. Head drain and opened up internal oil drain paths. I also don't run E85. I've never seen any oil in my catch can. Doubtful this is causing any issues.  Rear main seal - I have no visible leaks, but figured maybe it was my rear main seal. After now having added 2-3 quarts, I would expect oil to leak out the bottom drain channel and/or my clutch to be slipping.  Let me know your thoughts. With winter coming and taking the car off the road until spring, I'm fine with pulling the motor apart but I would hate to take it all apart and the turbo was the issue in the end.   
×
×
  • Create New...