Jump to content
SAU Community

Recommended Posts

Hi Guys,

Had a weird issue with my R34 GT-T today and wondered if anyone had seen this before.

Usually my engine light is on because my speed sensor is reporting an error (everything working fine though), but today my HICAS light started coming on and when it comes on my Tachometer seems to turn off!

The light comes on and off randomly, can be stationary at idle, or at speed, doesnt matter, but every time it comes on the Tacho drops to zero... then bounces back up when the light goes off. I also had the TCS OFF light and SLIP light on at one stage too, but they seem to have sorted themselves out after turning the car off for a bit. Took it for a spin after it cooled down and the TCS/SLIP were off but the HICAS/tacho issue still remains.

The car is driving absolutely fine with no performance or handling issue what so ever.

Would love to know if anyone has seen this before or has any advice. I'm currently searching for a replacement speed sensor for a R34 GT-T manual to fix the engine light too, Nissan want to sting me $300+... ouch!

Cheers,

Anthony.

Link to comment
https://www.sau.com.au/forums/topic/384820-hicas-light-kills-tachometer/
Share on other sites

dude dont send it to a workshop. all they do is exactly what any other backyard hobo does: "hmmm i wonder if this is the problem? *snap* nope. ill put it back... hmm i wonder if THIS is the problem..." etc.

i was a mechanic

removing a dash isnt bad. all you gotta do is lift out the display and look for a manky wire and put a piece of tape on it

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nissan/Pitwork is fine stuff. HKS is just marketing wank. I personally wouldn't do the idler if it is already new. If it looks and feels fine, it is fine. But as D says - it's cheap to add it to the job. The water pump ditto. Even more so. If it show no signs of problems, then it is nearly new - leave it.
    • 1. I can't see a location on your profile but you do mention GBP so I'll assume you are in UK. In Australia, CBC make a timing belt kit with the gears and idler and tension bearing and that is what I use without any problems. I'm sure OEM or HKS are also fine but I wouldn't pay extra for HKS over anything else. 2. Yes, I would always change the idler and tensioner and the stud and bolt that hold them in. Assuming they were all done last time it is highly unlikely you would have a problem, but they are very cheap to add to the job considering the time it will take anyway.  3. No, you don't need to lock them as such (I think that is more for engines without timing marks), but you should make sure they move as little as possible once the belt is off as you can hit pistons on valves if they move too far. As always, make sure you line it all up to top dead centre with the timing marks aligned before you take the old belt off.
    • How to wreak havoc at a bogans party... Swap out the goon bag hanging from the clothes line with oil bag... Watch chaos ensue during Goon of Fortune....
    • Hey everyone,   I’m looking for some advice on replacing the timing belt on my RB25DET Neo-powered 1998 Skyline. The engine was fully built about five years ago, including a fresh timing belt, water pump, and other essentials. However, since then, the car has only covered around 2,000–3,000 miles. It’s currently making around 650hp.   Even though the mileage is low, I know timing belts have a time-based lifespan too, and most recommendations suggest changing them every five to six years or 50,000 miles. Since I’m at that time mark, I’d rather not take any risks and plan to swap it out soon.   A few things I’d like to hear opinions on: 1. What’s the best belt for this setup? Should I go with an OEM Nissan belt, or is the HKS fine-tune a better choice given the power level? 2. Would you bother replacing the idler pulley and tensioner at the same time, or only if they show wear? 3. When swapping the belt, is it necessary to lock the cam and crank gears in place, or is lining up the timing marks enough? I’ve seen different approaches, and I want to make sure I do it right.   The water pump was changed with the rebuild and isn’t run off the timing belt, so I don’t see a need to replace it again. I just want to make sure I approach this the right way.   Any insight would be much appreciated. Thanks!
×
×
  • Create New...