Jump to content
SAU Community

R33 Gtst

alr33x

By alr33x,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

alr33x Grand Master

alr33x

Posted
Posted

hey guys looking to move on to bigger and better things so would like to sell my r33 had it for 2.5 years and its done 10,000kms since i bought it, female owner prior to me had done about 5,000kms in 2 years so barely gets driven but regularly serviced and well maintained any inspection welcome :thumbsup:

full respray about 3 months ago by Primal garage as being 15 years old was fading and not looking sharp, also wasnt planning on selling else would have saved my money and sold it as it was..

Weds Kranze 18x9.5+13 and 18x10+9

Bride Brix 1.5

Full exhaust with custom twin flutes

Coilovers,camber arms front & rear, hicas locker, car was a meant to be for drift and is set up perfectly for it straight up, possible a bit to low :D

Very clean interior great condition

Pretty much as you see it, have a lot of stock parts, seat/wheels/exhaust/steering wheel etc which is all going with the car, engine is standard aside from fmic and swapped out the coil packs to splitfires happy to negotiate and remove bits and bobs to lower the price i'm not worried if it doesn't sell ill likely part the whole car

any questions or more details pm or call 0422 318 946 leave a message i work long hours likely to miss the call, probably missed a bunch of stuff but whatever its a r33 they don't change much.

ASKING $15k low ballers come at me :thumbsup:

pics - Props to Ryan @ infintefocus

car has been lowered and cusco front camber arms installed since these shots updated pics to come.

infinitefocus-3948.jpg

infinitefocus-3953.jpg

infinitefocus-3952.jpg

cheers :cheers:

Link to comment
https://www.sau.com.au/forums/topic/384951-r33-gtst/
Share on other sites
  • 4 weeks later...
  • 1 month later...
alr33x Grand Master

alr33x

Posted
  • Author
Posted

*bump*

have removed wheels / seat / exhaust basically car is sitting stock wound up coilovers etc.

want it gone selling for $8.5k NO RWC i dont have the time to fk around with it but the car as it sits is bog stock. will take pictures and update

happy to discuss the other items if someone is interested.

Link to comment
https://www.sau.com.au/forums/topic/384951-r33-gtst/#findComment-6255881
Share on other sites
alr33x Grand Master

alr33x

Posted
  • Author
Posted

Sorry don't check thread often best to pm.

Wheels / seat aren't for sale into the car goes.

Re: road worthy as per above don't have the time and frankly its gonna cost money to get it obviously I'd rather sell it for less and the next guy can worry about it.

Link to comment
https://www.sau.com.au/forums/topic/384951-r33-gtst/#findComment-6268990
Share on other sites
  • 5 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      CD009 RB Conversion

      By TurboTapin · Posted

      These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • FRGTN1
      Fourth gear grind

      By FRGTN1 · Posted

      I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • RB2533
      UniClutch

      By RB2533 · Posted

      Yeah for sure that is peddle adjustment 
    • PotatoCake
      Attesa ETS Pro Install on R33 GTR

      By PotatoCake · Posted

      What are your thoughts on this after having it for a while, worth getting?
    • joshuaho96
      Fourth gear grind

      By joshuaho96 · Posted

      Downshifts are harder on transmissions than upshifts, the input shaft naturally slows down once disconnected from the engine so the synchros aren't doing all the work. There's no "natural" tendency for an input shaft to increase RPM. Something is not right there, I don't have a great answer on what. You can try a dedicated GL4 75W90, I plan to switch to Motorcraft XT-M5-QS which is supposedly a very good 75W90 for NB Miatas which have a weirdly sensitive transmission from the factory. I would chase down why your clutch is making a hissing noise, that's not normal. It might be no big deal but in the absence of anything else to investigate I would look at that.
×
×
  • Create New...