Jump to content
SAU Community

Recommended Posts

HI,

I need to do a general cleanup of all the parts i have floating around and im starting here.

Fuel Setup: $1000

6 x Rochester 660cc injectors

custom 3L under car surg tank

Various Earls -8 and -6 Auto-Flex lines and Swivel-Seal fittings

Bosh 044 Fuel pump

malpassie fuel reg with guage

Golan -8 Fuel filter

RB26 Apexi PFC with hand controller $700

RB26 single turbo exhuast manifold $100

Single turbo twin Air Pod fitting $100 post-61876-0-73173000-1323498339_thumb.jpg

Twin Apexi air pods and R32 GTR air flow meters $150

R32 Veilside side skirts $200 these are brand new never used

R32 GTR Twin Blitz Pop off valves $150

Stock pop off valves $60

Stock R32 GTR twin turbos with manifolds heat shields - were perfect when i pulled them off the car but have been sitting around so i would suggest rebuild. $200

R32 GTR ABS unit $80

Located in Sydney.

0414 509 399

post-61876-0-92866400-1323498340_thumb.jpg

post-61876-0-07313200-1323498343_thumb.jpg

post-61876-0-97558300-1323498475_thumb.jpg

post-61876-0-38354800-1323498477_thumb.jpg

post-61876-0-73662600-1323498479_thumb.jpg

post-61876-0-26651900-1323498482_thumb.jpg

post-61876-0-71681300-1323498507_thumb.jpg

post-61876-0-86099300-1323498526_thumb.jpg

post-61876-0-46531000-1323498528_thumb.jpg

post-61876-0-89946400-1323498544_thumb.jpg

post-61876-0-68591200-1323498595_thumb.jpg

post-61876-0-32152400-1323498597_thumb.jpg

post-61876-0-90360700-1323498600_thumb.jpg

post-61876-0-12305100-1323498603_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/385381-cleanup/
Share on other sites

Here are some pics and info.

I cant find the brackets for the pods..... but ill look some more.

the single turbo twin pod is about 170 wide and 260 long, internal dia of the large end is 94mm and 70mm on the small.

post-61876-0-69763000-1323681374_thumb.jpg

post-61876-0-99132200-1323681375_thumb.jpg

post-61876-0-16797500-1323681377_thumb.jpg

post-61876-0-35567600-1323681378_thumb.jpg

post-61876-0-58313300-1323681379_thumb.jpg

post-61876-0-60701800-1323681380_thumb.jpg

post-61876-0-54591500-1323681381_thumb.jpg

post-61876-0-62500400-1323681382_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/385381-cleanup/#findComment-6149370
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...