Jump to content
SAU Community

Recommended Posts

HI,

I need to do a general cleanup of all the parts i have floating around and im starting here.

Fuel Setup: $1000

6 x Rochester 660cc injectors

custom 3L under car surg tank

Various Earls -8 and -6 Auto-Flex lines and Swivel-Seal fittings

Bosh 044 Fuel pump

malpassie fuel reg with guage

Golan -8 Fuel filter

RB26 Apexi PFC with hand controller $700

RB26 single turbo exhuast manifold $100

Single turbo twin Air Pod fitting $100 post-61876-0-73173000-1323498339_thumb.jpg

Twin Apexi air pods and R32 GTR air flow meters $150

R32 Veilside side skirts $200 these are brand new never used

R32 GTR Twin Blitz Pop off valves $150

Stock pop off valves $60

Stock R32 GTR twin turbos with manifolds heat shields - were perfect when i pulled them off the car but have been sitting around so i would suggest rebuild. $200

R32 GTR ABS unit $80

Located in Sydney.

0414 509 399

post-61876-0-92866400-1323498340_thumb.jpg

post-61876-0-07313200-1323498343_thumb.jpg

post-61876-0-97558300-1323498475_thumb.jpg

post-61876-0-38354800-1323498477_thumb.jpg

post-61876-0-73662600-1323498479_thumb.jpg

post-61876-0-26651900-1323498482_thumb.jpg

post-61876-0-71681300-1323498507_thumb.jpg

post-61876-0-86099300-1323498526_thumb.jpg

post-61876-0-46531000-1323498528_thumb.jpg

post-61876-0-89946400-1323498544_thumb.jpg

post-61876-0-68591200-1323498595_thumb.jpg

post-61876-0-32152400-1323498597_thumb.jpg

post-61876-0-90360700-1323498600_thumb.jpg

post-61876-0-12305100-1323498603_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/385381-cleanup/
Share on other sites

Here are some pics and info.

I cant find the brackets for the pods..... but ill look some more.

the single turbo twin pod is about 170 wide and 260 long, internal dia of the large end is 94mm and 70mm on the small.

post-61876-0-69763000-1323681374_thumb.jpg

post-61876-0-99132200-1323681375_thumb.jpg

post-61876-0-16797500-1323681377_thumb.jpg

post-61876-0-35567600-1323681378_thumb.jpg

post-61876-0-58313300-1323681379_thumb.jpg

post-61876-0-60701800-1323681380_thumb.jpg

post-61876-0-54591500-1323681381_thumb.jpg

post-61876-0-62500400-1323681382_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/385381-cleanup/#findComment-6149370
Share on other sites

  • 2 weeks later...
  • 2 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update all   thanks to the workshop manual, it lead me back to checking fuses as mentioned central locking and door open lights worked when acc was switched on. diagram attached shows two points of power 1. ACC and 2.  Batt with the later being fused (#28) I did check the fuses using a multimeter but I must have stuffed that up also. Went back and checked the batt fuse in interior fuse box and you wouldn’t believe it… a blown fuse. replaced fuse and everything is now working as it should including the climate control   thank you all with your positive insight and knowledge.    
    • Where is the warning "That this thread is super old"   I just went into a 5 year old thread, went to do a reply, and couldn't see anywhere obvious a warning of it being super old
    • Duncan is correct. Pitwork (and Toyota's own cheap brand "Drive Joy") were primarily created as brands to sell other manufacturers car parts. It would be weird if Nissan sold parts for Toyota vehicles with a Nissan logo on it, so they created Pitwork to sell parts for other brans Toyota, Honda etc. They are not the same as Nissan genuine parts, although they *do* meet Nissan's standards for replacement parts. They aren't supposed to be a substitute for genuine parts, but a cheaper alternative that is better than Ebay fake parts from you-know-where.
    • Thanks GTSBoy, much easier to work with it now it's free!  
    • I _think_ that one has a christmas tree or some other retainer spike into a hole in that panel under it. Come in under it with thin scredrivers and just pry it gently up. If you rip the ears off the retainer pin....so what? Just stick it back down after with a bit of race tape and carry on with life.
×
×
  • Create New...