Jump to content
SAU Community

Recommended Posts

Hey my diff is leaking like a SOB and I'm gonna take off the backing plate to try and seal it up again. Do they run a gasket or siastic?

And is the backing plate easy to take off? Are the axles mounted in the backing plate and is the backing plate mounted to anything else under there?

Sombacisly my question is does it just pop off?

Thanks for your help.

Link to comment
https://www.sau.com.au/forums/topic/385501-gtr-diff-leak/
Share on other sites

Drain whats left of your oil, remove the backing plate, scrap off any glue/silastic/gasket on the surfaces, you can even give them a light oil stone if you can, wash teh surfaces with carby cleaner/ brake cleaner or another alcohol that dries clean, put a bead of blue rtv sealant on the diff backing plate, put it all back on and fill with oil

Link to comment
https://www.sau.com.au/forums/topic/385501-gtr-diff-leak/#findComment-6149962
Share on other sites

do the gtr's have a r200 rear diff..

if so when i put my 2way in, i got a new gasket from nissan. even at trade price i payed close to $90 bucks.

my thoughts are if your doing to do a job, do it once and properly.

Link to comment
https://www.sau.com.au/forums/topic/385501-gtr-diff-leak/#findComment-6150092
Share on other sites

Hey! Yeah I just went to Nissan now and the gasket is $83.07!! I'll still silastic the crap out of when i put it on. I also need to replace the seals where the axles come out from so the whole pumpkin needs to come out...

So remove exhaust, disconnect the drive shaft, disconnect the axles, 2 bolts ontop of the backing plate going into the sub frame then there is a bracket holding the diff up to the sub frame so disconnect them. And there is a pin up top holding the diff into the sub frame for extra support or something and the then just give it a wiggle back and front and it 'should' just pop out.... Just dont be under neath it!!

Link to comment
https://www.sau.com.au/forums/topic/385501-gtr-diff-leak/#findComment-6150224
Share on other sites

the shop that did my diff used automotive silastic on the cover of my diff. . . .no leaks,ive used selleys ALL CLEAR (already had it in garage) on a diff cover once before with no leaks either

Link to comment
https://www.sau.com.au/forums/topic/385501-gtr-diff-leak/#findComment-6157025
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I vote go red. Only because I hate keeping gloss black clean. Was no worries helping out either! Glad you've survived the rain outs of QLD
    • I would again like too thank Matt for his help in me sourcing the detachable hard top for the little red car, without Matt's assistance in inspecting it and locking it down, I can guarantee it would have sold before I could get up to see it,  and as that was the only available NC hardtop in Australia, I consider myself extremely lucky on multiple levels To say I'm more that happy would be an understatement And, it is 100% water tight, I drove through torrential rain coming back south, and by torrential, they type of rain that doing 40kph in a 110kph zone was a real thing, and even then, the standing water on the Hwy was deep enough to throw waves I'm also more than happy that the huge "BEASTS" that Matt calls dogs didn't eat me for lunch, I'm sure the sniffs and licks were more to "taste test" me, over being to friendly Now to work out what colour to get it painted, panel match, or gloss black........first world problems are real
    • Actually I might have figured out. Looks like there is a tab according to google images but it's hidden. Silly me.
    • No clips on this one like the other connector. Only that red tab that I can push slightly up.
    • For any loom connector that has an obvious release that resists pushing far enough to unclip, just spray some silicone lube into it. You might also benefit from using a bent screwdriver or small pick to push in the right place at the right angle.
×
×
  • Create New...