Jump to content
SAU Community

Recommended Posts

Nissan skyline ECR33

-5 speed manual

-Air conditioning and climate control

-Minor ADR regency legal modifications – 3' exhaust turbo back (quiet) , front mount intercooler, pod filter and a front whiteline strut brace.

-Car has passed regency as it is shown in the photos– the pod filter has 2 mounts and intercooler is mounted to chassis.

Car underwent a full exterior respray 12 months ago by VIPcustoms– not a cheap tape job like 95% of skylines, this was a bonnet, boot, doors off, windows out job. It has amazing clarity in real life.

New front windscreen and new front and rear window seals.

Rear guards have been rolled to allow for wider wheels/tyres

Stereo consists of a kenwood mp3/wma head unit with kenwood 6X9 and 6' speakers in the front doors.

Every electronic part of the car works – windows, mirrors, climate control, etc

Wheels are 17X8 and 17X9 Stern JDM imported items with common 235-45-R17 all around. Tyres on front are Kumho (80%) and rears are Dunlop with (60%)

Engine has been rebuilt (700km ago (13/12/11) - as fresh as it gets!) to OEM Nissan specifications with a NISMO metal head gasket. Standard size OEM Nissan piston rings, big endbearings, main bearings and water pump. Gates timing belt kit and NGK spark plugs were installed at the same time. All engine seals have also been done so it has no leaks/weaps internal or external!

Radiator, brake fluid and clutch fluid have all been flushed recently (12/12/11) well as the brake rotors being machined.

New high CCA battery (6/6/11)

This skyline drives A1 and will give years of service with just basic maintenance.

Please call/text 0432 224 954 for further information or to arrange a time to inspect. RAA inspections welcome!

P1130942.jpg

P1130948.jpg

P1130953.jpg

P1130954.jpg

P1130962.jpg

P1130967.jpg

P1130957.jpg

P1130930.jpg

P1130984.jpg

P1130982.jpg

Edited by hall sales
Link to comment
https://www.sau.com.au/forums/topic/385665-sa-skyline-ecr33/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I have one and it was at ~43.5PSI.
    • Put a pressure gauge on the fuel rail.
    • I've uploaded logs / the current map to Gdrive if anyone has any ideas. https://drive.google.com/drive/folders/1FPnr22Z-EilG7tYdHSi0Qb07P2jfFLKV?usp=sharing
    • I'm running a Haltech Platinum Pro with the stock map for the RB20DET + tweaks for my build. When I started it this morning, the IAT was at 32F/0C (Outside temp was ~42F) and the AFRs went off the scale for my AEM gauge. I let it run for ~30 seconds then turned it off. I then did a smoke test, by hooking into a vacuum line directly behind the throttle body, and confirmed there was no leaks ( i let the smoke tester run for ~5 minutes / confirmed it was generating smoke before hand ). I then started the car again, after fixing a power steering leak.... and it seemed to be happy for ~30 seconds (was at ~11/12), but then seemingly shot back up to ~18 again. I then let the car run for a few minutes, thinking this was just cold start related, but the AFRs never came back down. I didn't let the car fully warm up, so maybe this makes sense, but I'm not sure what to do? The AFRs, when I last ran it, were normal, but because of personal reasons I haven't been able to break in the car. It was rebuilt last year. Engine / Mod list: Supertec pistons Spool rods Kelford 270 cams and Springs Stock crank Deatschwerks 900cc injectors Walbro 255 (Wired directly to the battery relocated in the trunk) NKG Audi R8 Coil packs + Conversion Harnesses from Wiring Specialties Holset HY35 turbo Haltech Platinum Pro ECU Haltech boost controller (wired in for high boost RB25 Neo transmission + needed bits for the speedo to work  
×
×
  • Create New...