Jump to content
SAU Community

Recommended Posts

Alight guys, here are our trackdays for January 2012:

Wakefield:

8th - drift day

9th - Speed of the Streets

10th - Speed of the Streets

11th - Speed of the Streets

12th - Speed of the Streets

16th - Speed of the Streets

17th - Speed of the Streets

18th - Speed of the Streets

19th - Speed of the Streets

21st - Speed of the Streets

24th - Speed of the Streets

25th - Speed of the Streets

28th - Speed of the Streets

30th - Speed of the Streets

31st - Speed of the Streets

Marulan Driver Training Centre:

11th - Street Car Day

13th - Street Car Day

15th - Street Car Day

22nd - Street Car Day

23rd - Street Car Day

Im sure there is some days at eastern creek too, but i havent looked these up yet...

So as you can see there is plenty of track time for January! Hope you can get some time off work and i might see you there...i'm hoping to make a good chunk of these!

Link to comment
https://www.sau.com.au/forums/topic/386460-general-trackdays-in-jan-2012/
Share on other sites

wow, thats a lot of speed days! No one booked in for Jan at all?!

lol maybe it is even slower than Dec bookings...they gave the club a good deal for the Dec day.

Can someone convince Neil to take Cheryl to Marulan in late Jan?

lol maybe it is even slower than Dec bookings...they gave the club a good deal for the Dec day.

Can someone convince Neil to take Cheryl to Marulan in late Jan?

If he takes Cheryl... I'll look at taking the Coon out...



  • Similar Content

  • Latest Posts

    • Welp, too late already committed to the cam cover breathers to be welded on. I did think about adding a catch can in line with the drivers side sump breather as a phase 2 along with a drain to the sump on the original catch can but with an inline ball valve so I can have it closed if needed.    Likely a single breather would have been enough but I think I’m overcompensating to hopefully not have to empty my catch can and clean up oil over flow every session.    out of curiosity has anyone actually measured crank case pressure before and after various mods? I’m considering adding a sensor for science 
    • Is it a dog or synchro box? I guess either way, if it is new and crunching in one gear only, it has to come out and go back to the shop to check/measure as there is either an assembly or manufacturing issue
    • These are small points I should actually add to my original post. GKtech makes an extended slave line for this conversion. It's what I use, and it works well. You'll also need a CD009 slave cylinder.  S/R Chassis Z33/Z34 Conversion braided clutch line As for transmission sensors, you'll need to both extend the wiring and replace the connectors. I can't recall which is which, but one is your neutral switch and the other the reverse switch. As they are just switches, just test for continuity with your transmission in neutral or reverse to figure out which is which. Connectors:  VQ35 neutral Switch Connector | Wiring Specialties VQ35 Reverse Switch Connector | Wiring Specialties 
    • I’ll try and see it could be the release bearing. As for the 4th gear grind maybe clutch doesn’t disengage properly cause it is slightly like very slightly hard to go into first could be due to the slab cylinder pin being short uni clutch is a twin plate.   Ive attached some assembly photos hopefully you can open the link and see maybe detect what’s wrong https://share.icloud.com/photos/0dc2YvW__Hl6jl-l2_0jejjpg https://share.icloud.com/photos/09e0jkWOK-vP48c1cfY6u3ViA https://share.icloud.com/photos/0b4rDmh5R7pK7fb1VtND73a3g https://share.icloud.com/photos/05eeUi_6dC4DVi80jOUYDgb0g https://share.icloud.com/photos/06335TgY1XxyIJal_wkdQLhzw
    • Yeah for sure that is peddle adjustment 
×
×
  • Create New...