Jump to content
SAU Community

Recommended Posts

  • Replies 68
  • Created
  • Last Reply

Top Posters In This Topic

nope no wire cut but i had it stalled up nicely around 2500rpm at 5psi then bang 16PSI out of the box

correct me if i'm wrong but

Damo has Turbo back exhaust(dual because his fully hectic :P), Actuator, Boost controller and Shift kit.

Jethro has Turbo back exhaust, Shift kit and an aftermarket BOV.

I'm sorry I didn't get there guys.....will b trying super hard to get there in the next couple of weeks.....I'll also be trying to get the E-manage back on in that time.

Last run I did 4 k launch

As for mods turbo back exhaust airfilter boost and quick shift kit and rolling on 20s

How did you get it to stall at 4K without the brake wire cut mod? Mine will only get to about 2.5 - 2.8K without it.

In any case, my gut instinct (& some rudimentary testing) tells me the wire cut will be worth up to 0.5 sec off your 400m time. That should easily put your times into the 13's. For next time...?

Nice job guys.

hey all was a good night, good to catch up with 2 other stageas, hopeing to beat my tme 12mths ago of 14.4 ,after a few rubish starts and my last run i matched the same time 14.4 same dump and exaust nothing else. really happy with my reaction time of 0.032 and 60 foot 1.9 so those times i'm happy. next on the list is front mount.:banana:

How lame did you feel when they gave you the "smokem up" gesture and all you could do was shrug. lol.

Nice pics and times, I had better pull my finger out and get down to Calder before someone beats my 13.5s. Youre all getting too close for comfort. :cheers:

How lame did you feel when they gave you the "smokem up" gesture and all you could do was shrug. lol.

Nice pics and times, I had better pull my finger out and get down to Calder before someone beats my 13.5s. Youre all getting too close for comfort. :cheers:

i was just dodging the wet patch ROFL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This is the clearest explanation out of those: Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension. Basically you turn the engine with the tensioner bolt loose, then use the allen key to hold it while you torque it up. And yes after that a good guide is being able to twist it 90o in one of the long free lengths of the belt
    • good choice....I have a set of those and use them all the time including on this job. Plus, no-one wants a damaged nipple
    • Thanks all, went with nismo strengthened belt and all genuine nissan idler and tensioner Question on RB25DET Neo Timing Tensioner: I have a question about the RB25DET Neo timing tensioner. In one of the videos (minute 20 of https://www.youtube.com/watch?v=17y37BB9xnA and minute 27 of https://www.youtube.com/watch?v=Pb99s2E9xUg), the process suggests tightening the tensioner pulley installation bolt to the specified torque initially, and then loosening it slightly to allow the spring to set the correct tension. Is this the correct approach? The R33 workshop manual on page 74 states: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. The way this is written is confusing. Does this mean: Undo the nut, then reduce the tension by turning clockwise? Snug the nut so it stays in position without applying tension to the belt while removing the timing belt? The manual wording makes it sound like the nut will tighten automatically when you turn the tensioner clockwise , which is unclear to me.   Timing Belt Tension Adjustment Process: After loosening the tensioner nut, you turn the engine two full rotations by hand, which should set the correct tension. Once the tension is set, you tighten the bolt to 43 N·m (4.4 kg·m). Before tightening, you need to insert the Allen key into the hexagonal hole to hold the pulley in place while tightening the bolt. In one of the videos, it’s mentioned that you should twist the belt side to side, or turn it slightly to check if the tension is correct. The belt should turn halfway, indicating the right tension. However, I know that twisting or turning the belt is not a good idea. What are your thoughts on this? Finally, how can I ensure the belt isn’t overtightened? I’ve seen many cases where people have overtightened the timing belt.   Manual Excerpts: Page 74: Loosen the tension pulley installation nuts. Insert the wrench into the tensioner pulley hexagonal hole and turn it clockwise to tighten the installation nut temporarily. Remove the timing belt from each pulley. Page 77: Turn the crankshaft clockwise two full rotations with the tensioner pulley installation bolt in a loose condition. Insert a wrench into the tensioner pulley hexagonal hole to fix the tensioner pulley in place, then tighten the installation bolts. Tightening torque: 43–58 N·m (4.4–5.9 kg·m). The timing belt tension should be at the correct tension.
    • Takes a few minutes to malke one. Wood, or steel, or a wrap strap with some strategically placed solids to provide teh drive onto the ribs.
    • I would strongly suggest using the correct tool. They are not expensive and make the job much easier and don't damage the lock ring. Google "fuel tank lock ring removal tool" to see what I'm talking about. 
×
×
  • Create New...