Jump to content
SAU Community

Recommended Posts

post-64553-0-32796700-1325035959_thumb.jpgpost-64553-0-23371200-1325035941_thumb.jpgpost-64553-0-37950600-1325035948_thumb.jpgRB26

ATI 600hp Harmonic balancer damper & pulley kit

N1 water pump

HKS oil pump

Tomei oil gallery orifice

ARP Head stud kit

Cometic Street Pro 87mm MLS head gasket

Nissan full gasket set

HKS step-2 valve springs

R34 Greddy N1 Street Special camshafts, R34 CAS

Ported & Flowed headwork

Greddy timing belt

Precision adjustable intake & exhaust cam gears

Drive key, tensioner & idler bearing kit

87mm CP Piston kit - full block tidy up

Now i need turbos, i just went and had a look at a pair of Garret A/R 60 24m (apparently they have been highflowed) But his not to sure. His dyno sheet was saying 310KW and rekons he was runnign 22psi

Only reason turbos have been taken off his becasue he blew cylinder 2

These are just standard r32 gtr turbos? To me they look like they have steel wheels.

Any point in the right direction would be appreciated. Cheers.

Edited by sydking
Link to comment
https://www.sau.com.au/forums/topic/386675-what-turbos-to-match-this-build/
Share on other sites

Externally gated, old tech Nismo turbos... Talk about making a bad setup... Worse!

And all Nismo turbos were steel wheel.

As for turbos, usual questions apply.

What do you want/use of the car?

Budget?

Power goals?

Do you want response or top end

etc. etc. etc.

However, given the answers to the above 3 questions will pretty quickly end up seeing you using the search given there is plenty of info around.

Externally gated, old tech Nismo turbos... Talk about making a bad setup... Worse!

And all Nismo turbos were steel wheel.

As for turbos, usual questions apply.

What do you want/use of the car?

Budget?

Power goals?

Do you want response or top end

etc. etc. etc.

However, given the answers to the above 3 questions will pretty quickly end up seeing you using the search given there is plenty of info around.

Could you go into a little more detail of why you think they are a bad set up? what set up exactally? those turbos on that motor ect ect

I have just purchased everything in that pic for $500, So i can not complain with that.

I would be happy with 300kw. Responsive. And street driven.

Nismo turbos are 1970s design, they are laggy pieces of junk. Always have been, always will be.

That is why they are $500. They've been well covered in plenty of detail if you don't believe me.

Honestly if you've spent all that money building a motor. Why then go and buy $500 second hand, shitbag turbos?

300rwkw-330rwkw & responsive = Garrett -9

Of which there are more results than you can poke a stick at. There is even a "300-330rwkw GTR" thread :dry:

i used to have those turbos on my old set up, made 300rwkw untill the amfs maxed out

ended up selling them for 700 as a pair so u did alright

from memorty those turbos are rated to 310-320 hp per turbo so u would be able to 350rwkw on them, pretty sure someone made 370rwkw in the 26 dyno results thread...

they are plain bearing and yes they are a bit laggy but they sure as hell are fun to drive with, come on hard which makes them feel fast

a mate of mine just put some -9s on his GTR that makes about the same power as mine use to... personally i found them a bit liniar and boring

wouldnt use them for track where response counts, maybe on the street where the smile counts

-7 and -9 to me = boring, im sure alot of people wont like this reply as everyone seems to be hung up on response

if i had the old set up id have taken ya for a drive but its not to be

if u want the response then get the 9s so u have room for more power if u want it :cheers:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Boot is going to be replaced eventually. I just wire brushed what I could and rust converted. Then painted in rust kill primer. the spoiler also got repainted and plugs replaced on the ends. The under side of the bonnet is going to be black also, currently white. But red on the top side, same colour code as the silo to begin.
    • Hi guys, has anyone either purchased or built themselves a rotisserie for their car before? I can only just justify the need for one hence why I should just make one but at the same time, if I make one I can kiss another 4 weeks of potentially productive car working time goodbye because I'm building a bloody rotisserie....  I mainly want it for the application of the body deadener.  Cleaning the old stuff off, priming and then colour over the deadener doesn't worry me, it's just the application using the Schutz Gun that I feel would achieve a significantly better finish painting it side on and keeping the Schutz Gun upright.  I don't think they would work well on the side let alone almost upside down for some areas.  If the product I use (Terosun, etc) could work through a HVLP ok then it might be ok to apply without the rotisserie.   I can get one of these style ones for about $1200 which is pretty good value-     I reckon if I made one it would cost around $500 but it's more the time that it would take is more of a killer than the cost.  They look to hold their value pretty well second hand so I could always sell it after using it and realistically only lose $200-$300 at worst.  Or keep it and buy another project when this one finally sees the light of day... Anyone selling one...? Cheers!  
    • While it is a very nice idea to put card style AFMs into the charge pipe (post intercooler, obviously), the position of the AFM and the recirc valve relative to each other starts to become something that you really have to consider. The situation: The stock AFM is located upstream the turbo, and the recirc valve return is located between the AFM and the turbo inlet, aimed at the turbo inlet, so that it flows away from and not through the AFM. Thus, once metered air is not metered again, neither flowing forwards, or backwards, when vented out of the charge pipe. When you put the AFM between the turbo outlet and the TB, there is a volume of pressurised charge pipe upstream of the AFM and there is a volume of pressurised pipe downstream of the AFM. When the recirc valve opens and vents the charge pipe, air is going to flow from both ends of the charge pipe towards the recirc valve. If the recirc valve is in the stock location, then the section between it and the TB doesn't really matter here - you're not going to try to put the AFM in that piece of pipe. But the AFM will likely be somewhere between the intercooler and the recirc valve, So the entire charge pipe volume from that position (upstream of the AFM, back through the intercooler, to the turbo outlet) is going to flow through the AFM, get registered as combustion air, cause the ECU to fuel for it, but get dumped out of the recirc valve and you will end up with a typical BOV related rich spike. So ideally you want to put the AFM as close to the TB as possible (so, just upstream of the crossover pipe, assuming that the stock crossover is still in use, or, just before the TB if an FFP is being used) and locate the recirc valve at the turbo outlet. Recirc valve at the turbo outlet is the new normal for things like EFRs anyway. In the even of a recirc valve opening dumping all the air in the charge pipe, pretty much all of it is going to go backwards, from the TB to the recirc valve near the turbo outlet. But only a small portion of it (that between the TB and the AFM) will pass through the AFM, and it will pass through going backwards. The card style AFMs are somewhat more immune to reading flow that passes through them in reverse than older AFMs are, so you should absolutely minimise the rich pulse behaviour associated with the unavoidable outcome of having both a recirc valve and an AFM in the charge pipe.
    • Yep, in my case as soon as I started hearing weird noises I backed off the tension until it sounded normal again. Delicate balance between enough tension to avoid that cold start slip and too much damaging things.
×
×
  • Create New...